Question about Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television

1 Answer

Lamp Where is the lamp located on the tv an could you provide step by step how to get at it an replace it .

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 50 Answers

It should be in the rear of the unit. Remove two or three screws, and then loosen screws holding lamp, pull lamp out, and replace with new one. If it is not in the back then it will be in the front. Very easy to replace. If any questions please ask. Thank you.

Posted on Feb 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is lamp door located? I've read on here that my issue (blinking red lights) may be fixed via the lamp door but I dont know where it is...


I'm sorry for the difficulties you're experiencing in locating the lamp door of the TV. The Lamp door is located on the right side of the TV. I'm providing a photo with Lamp door is marked. Please review the below picture.

shajanrs_195.jpg

Thanks for understanding. Please let me know if you require further assistance.

Sep 27, 2011 | Sony KDS-60A2000 60" HDTV

1 Answer

I need to reset the lamp timer on a PT-61DLX76


I'm glad to provide the instructions to reset the Lamp Time of the TV. Once you replace the lamp of the TV, please follow the below steps to reset the Lamp time:

With the TV on, hold VOL [-] on the TV and [0] on the remote until a message appears on the screen.

Thanks for understanding. Please let me know if you require any additional help.

Jun 07, 2011 | Panasonic Televison & Video

1 Answer

Where is the lamp module located for a sony kdf 42we655?


Please read here: http://esupport.sony.com/US/perl/news-item.pl?mdl=KDF42WE655&news_id=84

From SONY:
If the screen becomes dark, the color looks unusual, or the LAMP indicator on the front of the TV flashes, it is time to replace the lamp with a new one (not supplied).

Use only a replacement Sony XL-2100U or XL-2100 for your TV. Use of any other lamp may damage your LCD projection TV. Contact your Sony dealer for a replacement lamp.

Click here to download step-by-step directions for replacing your TV's lamp.

Note: Before replacing the lamp, turn the power off on the main unit. Wait several minutes, then unplug the power cord. (The cooling fan will continue to blow for about two minutes after turning the power off.)

Be sure to allow the lamp to cool down completely before removing it. The surface of the lamp remains extremely hot for at least 30 minutes after the power has been turned off.

Mar 10, 2011 | Sony KDF-42WE655 Television

1 Answer

Where lamp is located for replacement and what r the steps I need to take to replace it?


Hello.
There is no lamp to be replaced in your TV. You are confusing it with newer DLP technology. Your TV is CRT projection technology, it has 3 CRT (picture tubes) and they are too expensive to replace.
Maybe just some adjustments could be made by professional, other than this - not much to do.
Regards.
Russ.

Dec 01, 2010 | Mitsubishi WS-65809 65" Rear Projection...

2 Answers

The tv is plugged in but it won't come on. I've taken off the back and there doesn't appear to be anything wrong but it's still not coming on by remote or manually pressing the power button. What should I...


  • Replace the lamp on the TV and make sure the cover is on -
  • Step 1Turn off and unplug the RCA TV and wait at least 30 minutes for the old lamp to cool down. RCA's lamps can reach heats of 200 degrees Fahrenheit, so make sure you wait the allotted time before beginning.
  • Step 2Find the lamp's access door in the lower-right corner of the back of your RCA TV.
  • Step 3Unscrew the screw on the access door with a flathead screwdriver, then grasp the two tabs and pull the door gently away from the remainder of the TV. Keep track of the screw and don't let it roll away.
  • Step 4Use the screwdriver to loosen the two screws holding the lamp itself in position. You don't need to remove the screws, just loosen them.
  • Step 5Pull the lamp out of its housing firmly, taking care not to force it or damage the surrounding housing. Note the position of the lamp in the housing as you do so; the new lamp needs to match it perfectly.
  • Step 6Insert the replacement lamp into the housing, taking care to place it in the same position as the old lamp. Tighten the two screws on its frame to secure it into position.
  • Step 7Replace the access door and tighten the screw into position. The RCA TV won't turn on unless the door is secured.
  • Step 8Plug the TV in and turn it on. Wait 60 seconds, then tune to a channel to see if you can receive a signal.
  • Step 9Place the used lamp in the box which contained the new lamp, seal it and contact your local sanitation department for instructions on disposing of it safely. (Some RCA lamps hold small amounts of mercury, so you can't just throw them away. )

  • Best Regards,
    Beach TV Repair
    Treasure Coast, FL

    Jul 04, 2010 | Televison & Video

    1 Answer

    Tv not workingt


    Open the lamp door located on the side of the TV. You will the see the lamp and one or two screws. Remove these screws and pull the lamp out. Check the lamp to see if it is either cracked/shattered or if there is a cloud either on the whole lamp or just on the stem of the lamp. If you see any of these on the lamp, then the lamp needs to be replaced. It is user accessible and putting in the new on is just as easy as taking it out. Your user's manual has step by step directions for checking and replacing the lamp if you need further instructions.

    Nov 02, 2009 | Toshiba 65HM167 65" Projection Television

    1 Answer

    Need to replace bulb in lcd panasonic


    After lamp replacement, make sure that lamp cover is properly fixed on its location and if TV still does not turn On then it is ballast power supply issue, qualified TV tech will fix it.
    If you think you can repair ballast supply and have enough knowledge about TV repair, let me know to provide you technical info about that.

    Oct 02, 2009 | Panasonic PT-50LC13 50" Rear Projection...

    1 Answer

    Projection TV - Red Lamp not on


    You can get a replacement Red CRT at the following link its used in good working order for 135.00 with free shipping compared to about 375.00 for new if available. The site also provides free step by step instructions on how to do the installation.
    here is the link http://servicemanuals.vstore.ca/

    Apr 04, 2008 | Televison & Video

    1 Answer

    Zenith model #m52w56lcd tv?


    For a really good step by step with pictures guide to replace it go to
    http://www.fixyourdlp.com/blog/?p=34

    For a good place to purchase the lamp go to http://www.discount-merchant.com/Original-Zenith-Projection-LCD-TV-Replacement-Lamp-p
    /zenith_m52w56lcd_lamp.htm

    I have found they have the best price on these replacement lamps. You might also check Ebay.

    Good luck!

    Feb 21, 2008 | Zenith D52WLCD 52" Rear Projection...

    1 Answer

    RCA SCENIUM TV (HD50LPW175) NO PICTURE.SOUND FINE.


    IF you would like help diagnosing your set. Go to the enclosed link. They have the service manual for your set and offer unlimited chat support for only 29.99. Just click on your sets manufacturer and you will see your model. Then click on the contact us link and provide your email address and they will email your manual and instructions on how to obtain your support. I am one of their techs. This manual contains step by step procedure for troubleshooting Your RCA DLP Light Engine
    http://servicemanuals.vstore.ca/

    Dec 27, 2007 | Televison & Video

    Not finding what you are looking for?
    Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television Logo

    Related Topics:

    55 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Televison & Video Experts

    matt martin
    matt martin

    Level 3 Expert

    1207 Answers

    The Knight
    The Knight

    Level 3 Expert

    71608 Answers

    Jaime Hernandez

    Level 3 Expert

    2291 Answers

    Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...