Question about Sony Z2X-1200 SPL Car Amplifier (1200 Watts) Car Audio Amplifier

2 Answers

Wiring diagram for sony xplod amp and how to bridge one

Posted by on

  • Marvin
    Marvin May 11, 2010

    no such diagrams is avail to the public.

  • Kenneth Nelly Dec 16, 2018

    Model number is xm-280gtx sony xplode

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

If you have the model number handy i can tell you

but most sonys are marked like this ..

+12v goes directly to the + termanl on the battry
GND goes to a solid metal object on the car (ground)
REM remote turnon goes to the remote turn on from your headunit

unbridged speaker outputs
+L positve left speaker
-L negative left speaker
+R positive right speaker
-R negative right speaker


ok to bridge a amp (must be capabul of doing so) look for a mono switch and set to mono ..

then take the +L channel put it to your subs + and take the -R channel and put it to the - of your sub

also set the cross over switch to LPF if your running bridged for a sub

if that is a bit hard to understand msg back with the model number of the amp and i can get u the orignal manual for the wireing diagram

hope that helps

Posted on Jan 27, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

I have s sony xplod was wondering if it was bridgable or not model number is xm-280gtx if so how to do it

Posted on Dec 16, 2018

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 14 Answers

SOURCE: wiring diagrams

Look here: http://server4.nodevice.com/down/3a1657608f40b3f62b18e5416ded9ec7/xm-zr607.pdf

Posted on Dec 07, 2008

  • 257 Answers

SOURCE: I Have a Sony Xplod 800 watt amp and 2 12 inch Sony Xplod subs

You should definately bridge them. Firstly, lay the 2 speakers face down next to each other. Note the connections +- +-. The first + will go to the amplifier. The next terminal(-) will be connected to the next speaker(+). Take the last(-) and connect to amplifier. Please note that your amplifier has a bridge section which is normally the first + and the last- on the two channels. Connect your woofers on the bridge.

Posted on Jun 09, 2010

  • 631 Answers

SOURCE: sony xplod 500w 4/3 channel

If the speaker is a 4 ohm DVC (two 4 ohm coils), you can't wire it to get a single 4 ohm load. Try connecting one coil to each of the two rear channels. It may not be as loud but the amp should operate without going into protection.

If the two 4 ohm coils are in parallel, the amp is driving a 2 ohm mono load. That's probably why it's shutting down.

Posted on Apr 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I connect a Sony xplod 1000 watt 2 channel amp to 1 10" dual 4 ohm voice coil 1500 watt planet audio subwoofer?


Connect one voice coil to one channel of the amp. Repeat with the other voice coil. Do not bridge the amp as your only choices would be series which would be an 8 ohm final load and cuts the amp power in half or parallel wiring which results in a 2 ohm load and very few Sony amps currently made can handle being bridged to a 2 ohm load.

Aug 28, 2016 | Sony Car Audio & Video

1 Answer

I have two sony xplod 12" speakers wich can hold


You only gave us the model of the amp so I will make an assumption that your 12" subs are the Sony XS-GTX120LW. First, they cannot hold 1200 watts a piece. They are meant to be powered with 350 watts RMS. They will hold 1200 watts peak. That means that 1200 watts for a few seconds will be ok. Past that and kiss them goodbye!

Next you indicated that bridged the amp. Since the subs are both 4 ohm single voice coils did you wire them in series or parallel?

It sounds to me like you wired them in parallel resulting in the amp seeing a 2 ohm load. The amp you referenced is only stable when bridged at 4 ohms.

Has the amp begun working again once it cooled down? If not you could have fried the outputs by having the resistance too low.

Dec 21, 2010 | Sony Xplod XM-1652Z Car Audio Amplifier

1 Answer

I Have a Sony Xplod 800 watt amp and 2 12 inch Sony Xplod subs


You should definately bridge them. Firstly, lay the 2 speakers face down next to each other. Note the connections +- +-. The first + will go to the amplifier. The next terminal(-) will be connected to the next speaker(+). Take the last(-) and connect to amplifier. Please note that your amplifier has a bridge section which is normally the first + and the last- on the two channels. Connect your woofers on the bridge.

May 28, 2010 | Sony XM-ZR1252 Car Audio Amplifier

1 Answer

I have an sony xplod 4 channel 600 watt amp


First are they in the same box? If so and they are sharing the same air space running one amp to both is best andwill perform better. One woofer could be over powering the other and or you could have a woofer problem. A lso your wiring coul be problem. When amp is bridged it changes the OHM reading and output your other woofer may not be rated at or able to handle a lower Ohm rating also it coul blow that woofer if it hasn't already hapened . Be careful. check woofers independently for operation and check the non performing woofer on an unbridged power source or amp. Hope this helps. Write back if not.

May 06, 2010 | Rockford Fosgate P112-200 Car Subwoofer

1 Answer

How do you bridge a amp to one subwoofer the amp is a sony xplod model xm-1502sx


http://www.docs.sony.com/release/XM1502SX.PDF

THE ABOVE LINK WILL TAKE YOU TO THE SONYSTYLE WEBSITES COPY OF YOUR AMPLIFIER'S USER MANUAL WHICH INCLUDES PRODUCT HOOK-UP AND DIAGRAMS. YOU WILL BE USING THE LEFT CHANNELS POSITIVE AND THE RIGHT CHANNELS NEGATIVE FOR A BRIDGED CONNECTION. THE CORRECT SPEAKER LOAD IS 4 OHMS MINIMUM. LET ME KNOW IF YOU NEED FURTHER ASSISTANCE....V

Jan 16, 2010 | Sony XM-1502SX Car Audio Amplifier

1 Answer

I have 2 1100watt sony xplods will they run off a 1000 watt amp


yes it will work, but it will only put out the power to the sub that the amp allows, ie : 100 watt amp puts out 100 wats.
you can also try reconfigering your wire to your subs, if your amp is 1ohm stable and your subs you can come off the amp with a bridge and run subs in series or parralell, this will dramaticly improve the bass

Apr 14, 2009 | Sony Xplod XM-1652Z Car Audio Amplifier

1 Answer

Bridge a two channel amp


i the search bar type in....subwoofer wiring diagram....then go to crutchfield and it shows you your options.......

Jan 28, 2009 | Sony Xplod XM-554ZR Car Audio Amplifier

1 Answer

Xplod amp


You have 3 power connection, +12v goes directly to your vechile's battery (make sure this is fused) REM connects to your head unit which tells the amp when to turn on and off (usually very thin wire, comnpared to the gnd and +12) Te gnd you already know where it goes. Then connect your sub to + and - speaker out put. If you run this bridged it will increase your output, must be 2 channel to bridge to 1 channel or a 4 channel bridged to 2 channels. Hope this helps.

Sep 13, 2007 | Sony Xplod XM-554ZR Car Audio Amplifier

2 Answers

Sony Xplod 1000 watt car amp quit working.


Almost all after market amps use 12v at very very low amperage to trigger the amp on. A temporary jumper from the battery plus terminal on the amp AFTER the battery and ground wires are attached should cause the amp to turn on. I would check to see if you have attached your speaker load correctly ESPECIALLY if you are bridging. Most of the blown amps that come into my shop are due to incorrect bridging loads from the speakers. Note that a 4ohm load bridged across both outputs of an amp will deliver a 2ohm load to each of the channels. When you parallel wire two 4ohm speakers together and then attached them to a bridged amp you will be putting a 1 (one) ohm load to each channel of the amp. Please don't make this mistake. It will fry your amp in about a month. Hope this helps. Good luck.

Feb 03, 2007 | Sony Xplod XM-1652Z Car Audio Amplifier

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

12,131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5013 Answers

Mike Duncan
Mike Duncan

Level 2 Expert

219 Answers

Dalynn Turner

Level 2 Expert

346 Answers

Are you a Sony Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...