Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

2 Answers

Washing machine wont stop filling up

Our washing machine will not stop filling up.  It started just on the rinse cycle and now it won't stop even in the beginning when it is putting water in for the first time.  We replaced the water level switch already (maytag #21001554) and it didn't help.  Any other suggestions?

washer wont stop filling on all cycles

Posted by on

  • 1 more comment 
  • Anonymous Mar 23, 2014

    machine fills up with water but will not go into wash. The time left for operation is replaced with the letters de

  • Anonymous Mar 23, 2014

    machine fills up with water but will not go into wash. The time left for operation is replaced with the letters de

  • Anonymous Mar 29, 2014

    when use a "full load" level for water to begin a wash, the "rinse" water then only fills to "med level". When use med. level for wash then the rinse only fills to low level. ??? Plus there is only less than two inches between the levels of med and full and the full level still doesn't even reach the top of the adjitator. I know stacks only hold small loads but this does not coinicide with previous ones top fill. Also the water at any level fills in splurges.

×

2 Answers

I had the same problem and found a piece of trash in my valve. The valves are controlled by a solenoid and are very sensitive.

Posted on Feb 29, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers

See if the water coming in is hot or cold by turning the water faucets off and on to see if one fills and the other dont and replace the valve

Posted on Feb 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 5 year old Roper washing machine fills up, washes/agitates the cloths, drains them when the washer get to the rinse line to start the rinse cycle it stops, and all I hear is a humming. The machine will...


I'm not familiar with roper washing machines so I'll ask the question does it have two fill hoses. Most European machines now only have one fill. If it has two then it sound like the machine takes the initial water from the one fill and the rinse cycle water from another. The humming sounds like the valve for the other fill needs replacing. These are quite inexpensive and easy to fit. Power off.. remove lid ....switch of water...take out valve when you establish which one is affected and replace

Oct 17, 2013 | Whirlpool WTW5700S

1 Answer

Beko WMP652W washing machine will start cycle but get stuck at end of wash, doesnt go onto rinse or spin any help please?


see the next steps and use the common sense: God bless you
When the cycle doesn't advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
8_2_2012_12_47_51_pm.gif

Aug 01, 2012 | Washing Machines

1 Answer

My washing machine wont start. The door lock


You will have to replace the door lock wax motor.

May 21, 2010 | Hotpoint Aquarius WF220 Front Load Washer

1 Answer

Washing machine wont hold water on any setting


raise the main drain hose to the top of the back control head. there may be a problem with the main hose being to low and the water is gravity siphoning out of the washer.make sure the washer is off when you lift the hose up but do not remove it from the wall,you should here water drain out once it has stopped draining restart you machine and it should fill to the proper level and quit then go into your wash cycle

Jan 31, 2010 | Whirlpool Inglis IP4400 Washer

1 Answer

Washer stop in middle of rinse cycle


All content © 2000 © 2009 Washerhelp
> Home / Repairs DIY washing machine advice (part 8) Washing machine sticks or stops mid-cycle repairs-sm.gif A very common fault on washing machines is when the program timer fails to complete the cycle and stops part way through. Many people blame the program timer for this but although it is a possible cause, there are many more likely causes for this fault. The program will stick if the heater isn't working, if the thermostat fails, if it can't fill up with cold water for the rinses, if it can't empty the water etc. There are too many possible causes of this fault to be able to give anything other than rudimentary advice. However, the common causes of a washing machine sticking that can easily be fixed are filling and emptying problems.
Check that the cold water supply is available to the washing machine, which is a common cause for sticking on rinses. If the washing machine appears to stop mid-cycle and isn't filling with water on rinses then see Washing machine won't fill with water (or no water goes into washing machine) before calling an engineer. If the washing machine can't drain the water out then it will stick on the rinses, or it will abort with an error code. If you can see water still inside the washing machine then check the following advice Washing machine won't empty water

Dec 02, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer will not complete cycle


washer fills up but wont start washing i can turn the knob just passed the numbers and the little marks and it starts washing and when it gets to the rinse cycle it wont rinse but when it gets to spin cycle it spins good

Mar 16, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Washer will fill fill with water but doesn't start wash cycle


it will fill but won,t spin, will throw out water as if it washed, then it take water to rinse but won,t spin ,then will throw out water as if it did , but clothes are soaked

Feb 21, 2009 | Roper RAS8445KQ Top Load Washer

1 Answer

Won,t drain on rinse cycle


Ok mc we need a timer at this point. You see the timer doing several steps different than before.

Nov 01, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Won,t drain on rinse cycle


There could be several causes for this, but probably a bad timer. One test for this...when it stops...is to turn it off...and turn the timer slightly clockwise...to the middle of the rinse cycle...and turn it back on. Does it run then?? Try advancing it to the spin cycle after the rinse. If it runs okay after you manually advance the knob...the timer is probably defective.

Jan 13, 2008 | GE WNCD2050AWC Top Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...