Question about CD Players

1 Answer

LASONIC DVD PLAYER

When we load the disc, the message appears "no disc"

Posted by on

  • mjjlsk May 19, 2008

    Reads No Disc

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 322 Answers

If under waranty take it back if not give laser a clean with a cotton bud diped in nail varnish remover ? if this fails then im sorry to say it seems that you need a new laser

Posted on Feb 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does a 'no disc' message appear on dvd player even though disc is present?


Could be simply a dusty laser lens. Try a cleaning CD first.

After that, it could be that the laser assembly has low power output. Some decks have the range to increase the laser power, but it's only a temporary fix. The emissions are dying so the laser assembly will need to be replaced sooner of later.

Aug 29, 2014 | Technics CD Players

1 Answer

Dvd stuck in home 7-cd/dvd changer


So you want to remove the disc without damaging the disc? so its ok to damage the player.
Put a cushion on the floor, put player on it.
Use a strong pair of pliers to crush and bend all the plastic parts of the loader near the disc, shake the player so that the disc falls onto the cushion.

Dec 21, 2013 | JVC CD Players

1 Answer

No dics display


That means it can not focus on the disc or that you are using the wrong disc type like a DVD in a CD player. Try cleaning the lens.

Dec 21, 2012 | Marantz SA8260 CD Player

1 Answer

Disc error appears when cd is loaded. Have tried with different cds


If the disc loads into it properly, the fault is with its laser pickup unit itself.

Apr 29, 2012 | Teac PD-H300 CD Player

1 Answer

My Sony 400 cd player will not play any cd's. When I hit play the blue light is in a continuous blinking mode then I get a message that says loading error. When I tried to open the door it was in super...


Your optics are either Really Dirty, or out of line and you would need a replacement optic pickup. If you are mechanically inclined, it's not a difficult repair and parts can be purchased thru lots of sites. First things first, pop the top and use "Dust-OFF" in the main chasis, it gets bad! Next, if you have a good CD/DVD player cleaner that uses fluid, run it thru a couple times then test any disc. If you don't have one, just about any convenience store has them. Just make sure it uses fluid!. If you still have an issue. post a comment and I can pdf you the schematic of the unit. it's pretty easy to read and follow if your a little more than a novice with electronics. Hope this helps

Jun 01, 2011 | Sony CDP-CX400 400-Disc CD Changer

1 Answer

Disc will not play appears to be skipping


There is a product called a cd/dvd lens cleaning disc. Worth the investment to have around.

Be sure discs are free of dust and scratches.

Apr 27, 2010 | Technics SL-PD6 5-Disc CD Changer

1 Answer

5 disc cd changer CC4000 will not read


All players need cleaned from time totime. Do NOT try to clean it with anything other than a CD / DVD lens cleaner. They are available almost everywhere that sellsBlank media. It will clean the lens without scratching or smearing it.

Dec 06, 2009 | Marantz CC-4000 5-Disc CD Changer

1 Answer

When I try to play a disc, the message


Hi there! Depending on when last the CD Player was serviced, I would think that the laser is at fault and needs replacement. However it may also be a mechanical fault. The only way to know for sure is to take the cover off and to see whether the disc turns at least a little bit before moving to the next. Also check whether the disc lifts into position properly and moves freely. If all the above proves OK, then the laser is probably at fault. Remember that there is current running through the unit so please stay away from any wires and boards when checking this. Best Wishes and Good Luck. JUS004

Aug 21, 2009 | Technics SL-MC400 110-Disc CD Changer

3 Answers

Will not read dvd, says loading, will stop and say no disc


Yeah I ve heard many people saying this. It is mostly because either the disc is damaged or the dvd lens reader has been damaged ..that is the only way by how it says "no disc" so better check with some shop around..or with the authorized dealer itself..ok

May 25, 2009 | CD Players

2 Answers

Disc Error/no disc messages


there is a strip that connects from the body of the lens to the circuit board take it off and replace it this will fix your problem you can contact dalbani in miami florida.to purchase the strip

Feb 17, 2007 | NAD T512 CD Player

Not finding what you are looking for?
CD Players Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top CD Players Experts

Dave Jukebox

Level 2 Expert

211 Answers

phil

Level 2 Expert

567 Answers

The Knight
The Knight

Level 3 Expert

68427 Answers

Are you a CD Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...