Question about Washing Machines

1 Answer

Hoover washer model VHD9143ZD

I have a hoover VHD9143ZD washing machine with a fault code E09, as this machine has been imported from Scotland to Australia.
Can anyone tell me what the code is and what may be causing it
Thanks in advance

Posted by on

  • bgd07 Mar 15, 2008

    Have the same problem.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Have the same problem. Have just looked in the service manual, it reads: Error 9 - Cancel the programme by returning the selector to the OFF position. Select again the programme and press the START/PAUSE button to switch the machine back on.

We recall having this problem with a previous Hoover washing machine and it was solved by cleaning the filter. The service manual recommends you clean the filter once a month. The procedure is as follows:
1) Open the flap

2) Only available on certain models: Pullout the corrugated hose, remove the stopper and drain the water into a container.

3) Before removing the filter, place absorbent towel below the filter cap to collect the small amount of water likely to be inside the pump.

4) Turn the filter anti-clockwise until it stops in the vertical position. Remove and clean.

5) After cleaning, replace the filter and lock by tightening the filter screw. Then follow all procedures described above in reverse order.

Hope that helps :)

Posted on Mar 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Display has been playing up. A message reading 'EOS' was diplayed just now. The machine has stopped working ?


Canon DLC: Article: Canon EOS Error Messages: An ...

www.learn.usa.canon.com/resources/.../eos_error_msgs.shtml

Canon Inc.Feb 6, 2012 - Canon has installed provision to display Error Codes in EOS SLRs for quite some time. Until fairly recently, the camera could basically display a single, or limited ... today's cameras do provide a wider range of possible read-outs, giving the ....Try removing the USB cable, and firing it normally to see if it now ...

problems installing digital solution disk - Canon Community

community.usa.canon.com/t5/PowerShot/problems-installing.../225
How to Understand Hoover and Candy Washing Machine ...www.espares.co.uk > Advice CentreJul 1, 2014 - Home & Office ... If a fault is detected in your washing machine, an errorcode is likely to flash up. ... how to identify error codes in a Hoover or Candy washing machine. ... code if the machine has a problem and this will either be displayed ...Now what I'm going to do is disconnect the machine and take the ...Error message E03 - Hoover Advice Centre - Hoover Serviceservice.hoover.co.uk > Advice CentreShould the error code E3 appears it is warning that the machine is not draining. You can easily fix this problem by removing any blockages from the drain pump ...Hoover Optima Washing Machine ' OPH ' Fault Codes

Dec 16, 2015 | Candy Domestic EVO14104L White 600 mm...

1 Answer

I have a hoover vhd 9163zd with error code E05,what component does it refer to being at fault,where is the component located


Error Code 05 is a NTC fault, either open circuit or shorted.
If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, the "E05" error code will be displayed.

Possible Causes / Procedure:
1. Unplug washer or disconnect power.
2. Check the water temperature sensor. Check connections to the water temperature sensor.
3. Check resistance of heating element, if present on this model. (abnormal = infinity).

Replace failed component. It could be the sensor or the temperature control module (NTC module).

Good luck.

Apr 20, 2015 | Hoover Washing Machines

1 Answer

Hoover VHD sensor Dry shows Eo8 vibrate badly and stops any suggestions please regards Peter


http://www.ukwhitegoods.co.uk/help/fix-it-yourself/specific-faults/3070-hoover-vision-hd-washing-machine-fault-codes.pdf

Mar 09, 2015 | Hoover Washing Machines

1 Answer

Wot is e16 mean


http://www.ukwhitegoods.co.uk/help/fix-it-yourself/fault-codes/laundry-fault-codes/3450-hoover-optima-fault-codes-carbon-brush-motor.html


looking here i see that error 16
tells us that the heating element has gone bad and needs replaced
or the wiring is bad

could just be a loose plug on the htc/ temp regulator

you can check it but its pretty clear by the error
so look to hoover spares ebay etc espares etc for the cheepest if you feel like replacing it yourself

Dec 09, 2014 | Hoover DYN8163D8X White 600 mm Washer...

1 Answer

Hoover washing machine showing H05 error


Error code: h05 coming up when i switch on the tumble - Fixya

www.fixya.com/support/t8443068-error_code_h05_coming
Feb 24, 2011 - Question about Washing Machines. Open Question ... SOURCE:Hoover washer/dryer VHW854D SHOWS ERROR. I have exactly the same ...

I have a 3 month old Hoover washing machine [DYN10146P ...

www.fixya.com > Forum > Washing Machines
Aug 11, 2011 - I have a 3 month old Hoover washing machine [DYN10146P] with aH05 fault. ... Have just looked in the service manual, it reads: Error 9 - Cancel the programme by returning the selector to the OFF .... show e-60 on screen.

Hoover and Candy Washing Machine Error Codes - YouTube

? 5:00
https://www.youtube.com/watch?v=kzhlvB2LjXg
Sep 1, 2014 - Uploaded by eSpares
Does your Hoover or Candy washing machine stops before .... I have a question: My Hoover displays the error code E08. what can I do to fix it?

Nov 18, 2012 | Washing Machines

1 Answer

I purchased this machine last year now after ending the programme i.e.washing door is not opening and it is showing error 14. Could u please help me out. Regards


Hi.


The fault E14 on Hoover washers indicate a problem with the heating circuit. Element, Thermistor and Central Control unit must be tested.

About error codes and troubleshooting Hoover appliances see the links below:

Hoover After Sales Service - Online Fault Finder

(Hotpoint/Creda/Indesit/Ariston Error Codes)

If you need parts or diagrams see this tip explaining how to find parts and diagrams for most appliances: Where do I find parts and diagrams for my appliance?
The sellers apply to USA market. Elsewhere see your local hoover distributor.

If you need to call a technician ring the customer service number listed on the owner manual or check your local Hoover website.

Regards.

Ginko

Sep 15, 2011 | Hoover Washing Machines

1 Answer

E09 PUMPS OUT WILL NOT SPIN


E09 ON HOOVER WASHING MACHINE WILL PUMP OUT BUT WILL NOT WASH OR SPIN?

Oct 31, 2010 | Hoover Washing Machines

1 Answer

Very noisy Hoover VHD9143ZD washing machine - just 2 years old


yes bearing housing get loose in plastic drum. needs drum replacement.

Oct 29, 2009 | Candy Washing Machines

2 Answers

Instructions for Hoover Washer Time 160E


i have a hoover soft wave maxi 1600 7.5kg AAA it spins and empty's and sometimes it don't what could be the fault

Nov 23, 2008 | Hoover AAA160 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...