Question about Barebone Systems

1 Answer

Canon MF8180 network printer. Was working fine until a recent power outage. Now it continues to tell me that the "papersize specified is incorrect" in spite of being correct in all of the setup features. It tells me that I have "A4" selected instead of "LTR", but I don't. As a result, I cannot print from any computer on my network.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 281 Answers

Reinstall it, after restart the computer than install it again.
It should work
I hope this was helpful .

Posted on Feb 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Unable to restart computer


The little green light is telling you that there is power to the Motherboard (MB) I would reset the CMOS on the Motherboard...boot into the BIOS to check that the hard drive is seen by the PC.and go from there...
Here is a link to the Asus Manual which shows you how to Clear the CLRTC..(CMOS) Look for section 4.3 on Jumpers.Clearing the memory built into the MB just sets it back to the defaults so dont worry about hurting anything while you perform this task...I can also tell you that When you clear this that there is no bells or whistles clashing cymbals or otherwise signal that tells you you have accomplished the task...you have to have faith that its done...Simply move the plastic jumper to the prescribed location and count to three then move it back to its original location...Secondly these parts are small and the writing on the MB is smaller so sometimes a magnifying glass is essential...Let me know how it works for you..
http://dlcdnet.asus.com/pub/ASUS/Barebone/Vintage-PH1/e1943_vintage-ph1.pdf

Asus also has the Recover Pro utility which is an always available recovery tool. It stores user data, applications and the operating system in the host-protected area of the hard drive. Users can easily recover system to their original factory conditions or to a more recent state without restore CDs. No need to worry about losing data due to virus attacks.

Feb 15, 2009 | ASUS Vintage-PH1 Barebone

1 Answer

Canon MX700


I had the same problem. Adding twain_32.dll to the Windowsfolder solved the problem. For people who don't want to search for it: Look Here.
Then you won't get this error but one saying to reinstall the printer driver. Just do it and the problem is solved.

Feb 28, 2008 | Barebone Systems

3 Answers

Waste tank near full


Hi
The waste ink take is actually just a felt pad that sits under the printer mechanism inside the case and absorbs the ink from your cleanings

Try this:
1 Power off printer
2 Hold RESUME button then press and hold POWER. (The beeper MAY sound once, or may not depending on your model.)
3 Hold POWER and Release RESUME.
4 Press RESUME twice then release both POWER and RESUME buttons.
5 When the indicator lights steady, press RESUME 4 times (for the S900, 3 times for the 8200 apparently).
6 Press power to set data.
7 Print away!

Let me know if that didnt solve your problem

Jan 10, 2008 | Barebone Systems

1 Answer

My Panasonic KX-P2123 printing under Windows 98 is continually generating the message "out of paper" when there is plenty of paper in it. I have tried different drivers, installing it as a...


use clean up utilitiy softwares to clean up temporary files that are no longer in use as they sometimes generate error alerts for errors that do not exist.good luck

Feb 23, 2008 | Barebone Systems

1 Answer

Printer networking


connect the printer to the router install the printer driver choose network printer it will then go off and find the printer and assign an IP address and make it availble for printing

Feb 18, 2008 | Barebone Systems

1 Answer

When the printer runs out of ink, the head moves accross as normal to let me change the ink, but while I am trying to change the ink cartridge, the head starts moving spontaneouly and jams with the ink...


Printers can do strange things, they are none the less mechanical in some respects. Whilst in operational mode, they can start up and resume a print job that has been spooling for hours ( usually due to network issues or overloads ) but getting back to your problem, i would suggest turning the unit off when the head is in the correct spot and insert the cartridge.


Additional info ( not required reading )
I have one theory is that most manufacturers are re-using older software drivers and updating where needed, and aren't getting away from the step by step type program enough. If a printer misses a step for whatever reason, it will continue to behave strangely until the unit has been put back in sync. Please someone tell me why is this so ? and if i am wrong, why does my printer fire up in the middle of the night, spit out 10 blank pages for no apparent reason ?

Jan 22, 2008 | Barebone Systems

1 Answer

Printer Problems


ok" take cartriges out of printer , water on clean cloth make it damp, wipe ink heads, take a pencile with eraser , use eraser on printed circuite on the back of cartidges to clean contacts, use eraser back and forth, wipe with cloth , put it back in the printer . may have to run printer tools to clean cartridges also

Jan 21, 2008 | Barebone Systems

Not finding what you are looking for?
Barebone Systems Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Barebone Systems Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

john smith

Level 2 Expert

366 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Barebone System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...