Question about DISH Network IR Remote Control

2 Answers

Replacement remote for bell expressvu

I git a replacement remote for my bell expressvu. How do I program the remote for the receiver to work. It was a remote for dishnetwork previosuly.

Posted by on

  • 2 more comments 
  • Anonymous Feb 14, 2008
  • Anonymous Aug 02, 2008

    I got a replacement remote control for the Bell Expressvu and I didn't get a guide with it. I cannot program it to work with the TV only the satellite box works.

  • Anonymous Sep 26, 2008

    Got Epressvu model 4500C !!!

  • Anonymous Oct 12, 2008

    I have a new universal "DISH NETWRK" remote. It works fine and it runs the Bell expressVU 3500 reciever. It turn my Toshiba TV on and off. But it will not adjust the volume level on my TV. HELP PLEASE

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Here is the link to pdf document: http://www.highspeedsat.com/pdf/satellite-tv/expressvu/remote.pdf

Posted on Sep 30, 2008

Cw-600s premium not working and no lid at all the remote control even when i i put new battery

Posted on Mar 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to program a Dish Network remote to run my Bell ExpressVu receiver.


Hi, Cheri Torres with DISH Network Customer Service here. I came across your post and wanted to see if I could help. While looking through all of our remote codes I unfortunately did not find any codes for a Bell ExpressVu receiver. What you can try is running a power scan on your DISH remote which basically can sometimes find the code for you. I will list here for you the instructions for running a power scan after this post. I hope you find these instructions useful and if you have any further questions or concerns feel free to email me at Cheri.Torres@Dishnetwork.com. :)

Instructions for a power scan
  1. With the desired equipment on, press and hold the correct Mode button (i.e. SAT, AUX, TV, VCR) until all mode button back lights illuminate, then release.
  2. Press and release the Power button. AUX Mode: Before pressing and releasing the Power button
    • Press 0 for a TV
    • Press 1 for a VCR/DVD
    • Press 2 for any other device.
    Then Press STAR (*)
  3. Press the Up button once a second while pointing the remote at the desired equipment. Note: If the code for the equipment comes up, the equipment will power off.
  4. As soon as the desired equipment turns off Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.

Feb 08, 2011 | DISH Network IR Remote Control

3 Answers

I need a satellite Bell express Vue code (3100) I can't use the remote control Dish!!!!


Programming an Expressvu remote control can be frustrating. There are two basic ways of doing in it. The first one involves knowing both your TV brand name and also knowing the proper code to input in your remote. The second method is doing an automatic search. The following is a step by step procedure in how to program your dish network or Expressvu remote.

1)Make sure your TV and Satellite Receiver is ON.
2)Press and hold TV button until all lights on the side of it flashes. The TV button is the second button on the Top left hand side corner of the remote control.
3) Release that button, then press & release RED Button. You will notice TV button is stays on. If, it doesn't stay ON, you must repeat step 2 & 3. Otherwise, your batteries are low, you MUST change then.
4)Press and release the UP Arrow Key on the remote until TV turns off. Notice the UP arrow key button is the button below the volume keys (Stop button for VCR.)
5)Make sure you are aiming remote control to TV while pressing and releasing UP arrow key button. When you find the right code, the TV will turn OFF.
6) Immediately after, TV turns off, press # key.

Jan 23, 2010 | DISH Network IR Remote Control

1 Answer

Remote Control Programming


it is so good to hear from you friend. the replacement remote that you need is on newremotecontrol.com. the number that you are looking for is 148058621. this remote cost 24.95. thank you for writing and please rate my solution.

Nov 18, 2009 | Sony Remote Controls

1 Answer

Bought a dish identical remote to Bell Expressvu.


You may need to program to your equipment, go to dishnetwork.com/tech and that will show you how to address your remote.

Nov 06, 2009 | DISH Network IR Remote Control

1 Answer

Need remote code for programming a bell expressvu receiver


Here for the Jensen remote just click below;

Here is link to the manual:

http://www.remotecodelist.com/remotes/jensen/JR300C.pdf


Here is some helpful information I found:
Without the code on JER-323:
1.Manually turn on the component you want the remote to control.
2. Press the device button, example:( TV) and the (power button) for 3 seconds until the (on/off button stays lit).
3. Once the (on/off) button is lit, press the (on/off) button until the unit (the TV or unit you are trying to control.) turns off.
4. When the code is located, press the (stop) button at the bottom to save the code.
Here are some codes I found for the Jensen 323:
GE VCR: 2000, 2013, 2021, 2022, 2053, 2087, 2089, 2091, 2115, 2120
Motorola Cable Box: 5000, 5003, 5046, 5047, 5052
Mitsubishi TV 0093, 0150, 0178, 0019
JVC VCR 0067, 0041, 0008
JVC DVD 0558, 0623

Hope it may help you;

Regards,
VOTIT

Jan 27, 2009 | Jensen 143307 Remote Control

1 Answer

Samsung BP59-00071B remote wont program Sanyo VCR DVD combo


Try 543. thats what I need to record to my Sanyo VCR via Bell ExpressVu satellite receiver.

Nov 11, 2008 | Remote Controls

1 Answer

Code for satellite bell (expressview)


Programming an Expressvu remote control can be frustrating. There are two basic ways of doing in it. The first one involves knowing both your TV brand name and also knowing the proper code to input in your remote. The second method is doing an automatic search. The following is a step by step procedure in how to program your dish network or Expressvu remote.

1)Make sure your TV and Satellite Receiver is ON.
2)Press and hold TV button until all lights on the side of it flashes. The TV button is the second button on the Top left hand side corner of the remote control.
3) Release that button, then press & release RED Button. You will notice TV button is stays on. If, it doesn't stay ON, you must repeat step 2 & 3. Otherwise, your batteries are low, you MUST change then.
4)Press and release the UP Arrow Key on the remote until TV turns off. Notice the UP arrow key button is the button below the volume keys (Stop button for VCR.)
5)Make sure you are aiming remote control to TV while pressing and releasing UP arrow key button. When you find the right code, the TV will turn OFF.
6) Immediately after, TV turns off, press # key.

Jan 03, 2008 | Remote Controls

Not finding what you are looking for?
DISH Network IR Remote Control Logo

7,308 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Remote Controls Experts

john milligan

Level 3 Expert

512 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you a DISH Network Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...