Question about Intermec EasyCoder PC4 Label Printer

1 Answer

Error Message My Printer is giving me an error message saying Paper Seection Error. Brother M4318 printer not working & coninue blink red light

Posted by on

  • ukneqascpt Mar 20, 2008

    21mm x 21mm labels on a roll. Cannot get labels to backup to top of form so always get blanks between

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Clean the paper sensor located at the centre of the mechanism .
Switch ON the printer While holding Feed key down, Printer will enter into self test mode, it will stop after printing self test label.
To take out priter from HEX DUMP mode press feed key for 3 seconds. now printer is in Normal working mode.
Try feeding labels, only one label should advance at a time.
This is the calibration procedure.

Posted on Aug 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have to print out a paper right away, could you help me?


If it still prints ignore it.
if you rather call the vendor. Ifyou're under warranty. They may replace or repair it.

Apr 18, 2015 | Brother MFC-7220 All-In-One Laser Printer

1 Answer

Printer blinking red and showing letter E


Error description:

The Attention (red) light is blinking. There are six possible causes that will display the Attention light pattern:

-Paper out
-Door open
-Print cartridge missing
-Paper jam
-Paper sensor jammed
-Duplexer error

Solution :
After the cause of the problem has been addressed, pressing GO will cause the printer to attempt to recover from the cause of the error. If the printer is unsuccessful, it will continue to display the Attention message until the cause is remedied.

Pressing JOB CANCEL will cancel the print job and the printer will return to the Ready state (Ready light on) unless there is a paper jam still in the printer or the print cartridge is not in the printer.

For more details visit the link below :

Resolve Printer issue

Jun 09, 2011 | HP DeskJet F380 All-In-One Printer

1 Answer

Top light blinking. Getting paper jam error message repeatedly. Cleaned the pad. did a nozzle check, replaced THREE cartridges. Did not give my blood type yet. How to fix? The waste pad is not...


This error message is displayed by the printer when paper is jammed in one or more locations. In such a case, users are recommended to remove the jammed paper from the specified location. The entire paper path must be checked for any pieces of paper. To stop the message, open and close the top most cover of the printer. Lastly, verify the flags and the sensors. If the problem persists, the cause of the error message could be a broken sensor or sensor lever.

Feb 18, 2011 | Epson Stylus Photo R2400 InkJet Printer

1 Answer

When i hit "print" the


Does the red light blink or stay on sterady?


Issue: The Compact Photo printer power button is blinking red.


Solution: Turn the Compact Photo printer off, then back on again.

"Paper Jam" appears on the digital camera LCD Turn the printer off and disconnect the power cord from the printer. Then reconnect the power cord and power on the printer. If the printer fails to eject the paper, the printer may require service. Contact the Canon Customer Support help desk for assistance.


When you power down I would recommend also unplugging the printer from the power supply (wall outlet). Let it rest 5 - 10 minutes and then plug back in.

The manual says a blinking red power light indicates a problem in the printer, but the only solution provided it to turn off and on.

If there are no paper jams, and no other error messages hoepfully a completr power down will clear the error.


Issue: Printer's power button lights red without the camera's LCD monitor displaying any error message.

There is a malfunction in the printer.

Remove the paper from the paper-handling slot and take up any slack in the ink sheet. Turn the printe's power off and turn it on again.

If none of this helps I would check to see if my driver is current:

http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/selphy_compact_photo_series/selphy_cp510#DriversAndSoftware

Trust this is helpful. Please vote. :)

Dec 11, 2010 | Canon Selphy CP510 Thermal Photo Printer

1 Answer

Middle light blinking message says paper


Look for any small rips of paper caught in a sensor back there. There are little "fingers" that the paper runs over and its all timed. if one of those sensors are jammed with something or sticky, error messages.

Sep 22, 2009 | HP DeskJet 550c InkJet Printer

1 Answer

Both red lights on my printer are blinking


Blinking wit general error message : head carriage error. It cause by head cannot move to parking position or chip at ink tank not good connected. Try to use another chip. Just turn off printer for a moment for clearing epprom.

Nov 09, 2008 | Epson Stylus C83 InkJet Printer

2 Answers

Brother MFC-9420CN Paper Jam B!!!


open and check for paper in the back. sometimes a corner may have been caught in there and will give you the error.

jb

Oct 25, 2007 | Brother MFC-9420CN All-In-One Laser...

3 Answers

Error Message


Hi there,
"Open heat error" ---
open the back cover and you find a two wire connector just near ribbon connector it is thermistor connector the printer is sensing this connector as open or not connected explore and fix.
Good Luck!!!
neo

Sep 19, 2007 | Samsung SCX-4100 All-In-One Laser Printer

Not finding what you are looking for?
Intermec EasyCoder  PC4 Label Printer Logo

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intermec Printers & Copiers Experts

pkwc

Level 2 Expert

254 Answers

Paul Bade

Level 3 Expert

1392 Answers

Shahzad  Waseem...
Shahzad Waseem...

Level 3 Expert

746 Answers

Are you an Intermec Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...