Question about Pioneer PRO-200 60" Rear Projection Television

1 Answer

Pioneer Pro-118 won't turn on

I have a Pioneer Elite Pro-118 sans remote, and there are no techs within 50 miles of me.  Problem: won't turn on: A red led lights for the 'main Power' button,  but pushing the 'standby/on' button makes the MP button go green, but them pop off as if a circuit blew. I can then push the MP button twice to start over, but same thing happens. Any thoughts on which switch might be bad, and where I could order one? thanks rp

Posted by on

  • 4 more comments 
  • rclennon Feb 16, 2008

    thanks for trying, but it didn't work. I replaced all 4 fuses. 

  • rclennon Feb 19, 2008

    nope. all were good that I took out.

  • rclennon Feb 20, 2008

    don't have a manual, so I don't know where these are located.


    Thanks for help.

  • rclennon Mar 04, 2008

    ctf 1800: can you explain your question/comment "does this set have the st'sk in them that and check the horz output transistor"?


    I'm not sure where these are located on the set, as I don;t have a manual. thanks!

  • tataka Mar 21, 2008

    I am having the same problem. In stand by you use the remote to start the set. The light goes green and then goes off in about 3 seconds. If you turn the power completely off and leave it off for a couple of hours you can turn it on and it will work. It may work 15 minute, it may work for hours. The set is 13 years old. Is it worth fixing?

  • Gordeley May 16, 2008

    We are having the same shutting off issue with the Pioneer Pro-118. It is very frustrating. We have taken off the back, moved it away from the wall, etc., etc. One day it can run all day long and the next it won't even power up. This is very frustrating and we are not electronics inclined and not sure if it is worth paying to have it fixed. Help please!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 4,402 Answers

Take off back cover. The problem power board is to the right of the board where the power plug feeds into the TV. There is a large white fuse right bend the power plug. With a meter it read ok; about 8 inches deeper into the TV on that board was the resister next to two fuses. My 4 amp 125 volt fuse did not read on my meter. After replacing, it worked fine. Check all three fuses while you're in there.

Posted on Feb 12, 2008

  • Cary Farah
    Cary Farah Feb 16, 2008

    were any of them bad?

  • Cary Farah
    Cary Farah Feb 19, 2008

    does this set have the st'sk in them that and check the horz output transistor

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Pioneer Elite Pro-118 rear projection tv


ya mine did something close to the same. at the moment i covered the blue canon inside the tv now the picture isnt 2 of eveything. the tv comes apart easy from the front good luck mike

May 02, 2010 | Pioneer PRO-200 60" Rear Projection...

1 Answer

Pioneer Elite Pro 100 TV, turns on, NO VIDEO, won't turn off


Retire it? Are there no television servicers in your area? Being a tech wizard seems to be a requirement for merely hooking up and operating some systems, but repair is still a valid option for most electronic items. Consult an experienced electronic technician specialized in television repair, another 10 years of operation is possible. Needless disposal only depletes our landfill space.

Sep 05, 2009 | Pioneer PRO-100 TV

1 Answer

Pioneer elite pro-530hd tv---no picture at all!


I have a 532nd 53 that shuts off and red stand by lite comes on in the back. If you wait awhile and unplug it and plug it back in it will come on again and then shut off after an hour or two

Jan 19, 2009 | Pioneer PRO-530HD 53" Rear Projection...

1 Answer

Pioneer Pro-118


you need two STK392-110 convergence Ics they are available at the following link with free instructions.
http://servicemanuals.vstore.ca/

Nov 30, 2008 | Projection Televisions

1 Answer

Pioneer elite pro 118


if the tv is more than 10 years old no its not worth replacing the power supply.if its 5 years or newer yes it owuld be worth the money

Jul 17, 2008 | Pioneer PRO-200 60" Rear Projection...

1 Answer

Problem with pioneer elite pro-99


We are having the same problem of the Pioneer Elite Pro-99 turning itself off all of a sudden. The red 'non' power button comes on as if we had turned it off remotely.
We would love to resolve this. If you can help let us know.

Jun 30, 2008 | Pioneer PRO-99 TV

2 Answers

Pioneer Pro 1009W


Replace conv ICs. This usually does it.


Mr Bob
www.imageperfection.com

Jan 11, 2008 | Pioneer PRO-1009W 57" Rear Projection...

2 Answers

Cannot program my universal remote


buy the exact remote from parts store.com

Oct 25, 2007 | Pioneer PRO-200 60" Rear Projection...

2 Answers

Is this Pioneer Elite Pro 118 worth fixing?


You most likely have cold solder connections on the convergence IC's or on the B+ sources for the convergence. The longer you wait to have this simple repair done, the worse this will get and cost you double or maybe even triple of what it will cost now. Good Luck

Jun 28, 2007 | Pioneer PRO-200 60" Rear Projection...

Not finding what you are looking for?
Pioneer PRO-200 60" Rear Projection Television Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

zorbrack

Level 1 Expert

19 Answers

Are you a Pioneer Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...