Question about Dishwashers

3 Answers

Dishwasher whirlpool 6th sense ADP 2966 WHM

Hi my dishwasher has stopped mid cycle the make and model is listed above. The start button is flashing periodically and to the right of the start delay is F2 guess this is the fault. I don't have a hand book as it was given to us it has been working fine since christmas. Hope you can help!

Rachel Moulson

Posted by on

  • malaga6502 May 03, 2008

    hello i have the same problem

  • robert samples May 11, 2010

    first open and close the door make sure it latches then try cancel /drain and let me know what happens

×

Ad

3 Answers

Kgfdgdgd

Posted on Apr 09, 2008

Ad

F2 = flooded base (got a leak)

Posted on Jun 14, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have try but it same problem F2

Posted on May 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't it work?


please provide model number of the Dishwasher and the exact keys where the three lights glow.
Perhaps a photo without flash will help

Mar 29, 2016 | Samsung Dishwashers

1 Answer

Why did my quiet partner II whirlpool dishwash just stop mid cycle?


see this possible causes:
Water-heating cycle
heat, wash, and rinse has the 3 cicle, principal problem is the heat cycle, when the water reach the level ( by heating water elements) test the heating elements , most ot the time fixing this .the problem is o.k
Timer
sincerely. God bless you

May 04, 2012 | Whirlpool Dishwashers

1 Answer

Hi Indesit IDL700 Dishwasher. Stopped mid cycle by


The main processor was interuppted and so has hung up or is faulty. Remove the main plug and press on the control pad of the washing machine to drain off any residual voltage that is remaining on the main board and which seems to have hung up the processor.When the plug is plugged in and switch please hold down the start/stop button.
If there is no result after plugging in the machine then the main controller board is a suspect. You can remove the control board and check the connectors, check the main door switch , if possible clean the connectors/ contacts as a last chance.

Sep 05, 2011 | Dishwashers

1 Answer

Dishwasher starts to work but after 30 seconds stops and two lights start flashing on pannel


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.Service manual below, if the above doesn't help. http://appliancejunk.com/ge/dishwasher/31-9137.pdf

Jun 24, 2010 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Restarting the dishwasher


Hi Kathleen,

Welcome to Fixya, you came to the right place.

I`m not sure what model you have, but typically you should be able to select another cycle by choosing a button and pressing it twice quickly.

For instance if you want`"normal" press the normal button twice in 2-4 seconds and it should go to normal cycle.

Let me know how you make out. Good luck and thanks for visiting "fixya".

Please take moment and rate this solution favorable if indeed it helped you, if not let me know and we`ll move forward from here.

macmarkus :)

May 05, 2010 | Bosch Dishwashers

3 Answers

Frigidaire dishwasher pld2855rfc stuck on lower rack, 65 mins, hi-heat temp and sanitize lights flashing


http://www.retrevo.com/support/Frigidaire-PLD2855RFC-Dishwashers-manual/id/1060bh943/t/2/
user manual above.
http://136.166.4.200/contents/Dishwasher/LDS5811/LDS5811_Service_Manual.pdf
service and repair manual, above is the user manual.
Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com

http://www.applianceblog.com/mainforums/forum17/
http://www.applianceaid.com/dishwash.html
You need to use the service manual, work through, all the procedures, to isolate your problem,and repair. The DIY sites will also help

Also try to unplug and leave unplugged for 5 - 10 mins, and reconnect, this sometimes "Resets" it. Also it may NOT apply, but the Fix below regardless, works, many times, and is well worth a try.
Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.

Apr 25, 2010 | Frigidaire PLD2855RFC Dishwasher

1 Answer

Mdb6650aww code flash: Rinse Cycle & Wash Button.unit inoperative


You might try running the diagnostic mode which can be model dependent. To find your particular method to do this .... unscrew and remove the lower kick plate under the door. The service technician paperwork is usually taped to the kick panel or the tub or side wall. Within that paperwork should be the work process to run through the diagnostic mode. The work process is one of pushing various control buttons in a sequence within a quick time frame and repeating 2-3 times.
If that fails ... other potential reasons run the gambit of a bad control panel (or loose wire connection to the panel), bad heating element, etc
Good luck on your troubleshooting!

Jan 20, 2018 | Dishwashers

1 Answer

DU1100 Stops mid cycle.


main control cpu unit failing
needs to be replaced

May 09, 2008 | Whirlpool 24 in. DU1100XTP Built-in...

1 Answer

Two Green Lights Flash Mid Cycle.


It's possible that there's a fault in the drying heater coil, but I couldn't tell you for sure without looking up your machine. If you could locate the model number tag on your machine and write down the exact model number and serial number, then I could likely give you a more informative answer. ;)

Aug 08, 2007 | Kenmore 24 in. 15252 / 15254 / 15259...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

2,397 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

82285 Answers

Brad Brown

Level 3 Expert

17473 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...