Question about Quantum Fireball Plus AS (QMP30000AS-A) 30 GB Hard Drive

3 Answers

Need a jumper diagram

I need to know where the jumper is to be put on for master and slave

Posted by on

  • Anonymous Apr 24, 2008

    I don't have a disk to start up my drive Quantum Fireball Plus AS

    I don't know where to set the jumper

    Thank You

    Dave

  • Anonymous Aug 12, 2008

    jumper settings

×

3 Answers

Quantum 30gig

Posted on Jun 26, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

On my quantum frieball plus AS 20.5 goes as follows:if having drive in hand power is to left, move right to jumpers !
Jumper config table on mine says, reading left to right now.
far left no jumper
PK is next pair: park is (slave)
CS is next pair: cable select is(master or slave)
DS is next pair: drive select is(master)
this is righ off the top sticker of my drive, stop laughing I know it's near obsolete but still works.
good luck.

Posted on Feb 07, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,985 Answers

This is usually marked on the drive as a label and moulded onto the end cap.
If this does not appear to be so then experimentation is the only way


: : ::
|
The far left is usually the master .

Posted on Feb 12, 2008

3 Suggested Answers

  • 46 Answers

SOURCE: how to tell which jumper is master and which is slave

normally most harddrives are the same, copy the other one see if that works.

Posted on Mar 28, 2008

  • 2666 Answers

SOURCE: install old maxtor HD on newer pc, change it from mster to slave

From your own description Slave : Off therefore remove the jumpers

Posted on Jul 26, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the jumper settings on the drive for the following? Cable select Slave Master


For Slave/Master set up most hard drives have a little diagram on them showing you where to put your jumpers for master and where to put the other one for slave. All hard drives are different. But on your diagram it should say "MA" for master, "SL" for slave and "CS" for cable select.

For Cable select you have to set jumpers to cable selected which should be on the diagram on your hard drive. You will need an 80 conductor IDE/ATA cable. The master conductor is at the end of the cable and the slave conductor is in the middle.

Mar 25, 2011 | Computers & Internet

3 Answers

I have a maxtor 51536h3 harddrive, I need to know the jumper settings for running single as a master and slave to transfer the data to another harddrive. THANKS


If you have two hard drives on the same IDE cable, then set one as Master and the other as slave.Set which ever one has your operating system on it as the master (though it doesn't really matter). Once you get them both plugged in and your computer boots up. You should see both drives and can transfer data as you see fit.

Mar 03, 2011 | Computers & Internet

3 Answers

What happen if i dont put jumper in a hard a hard drive?


If you don't put jumper in harddrive is detects it as cable select means if you connect your harddrive to middle socket of ide cable and then it detects it as slave but if you connect it at the end of ide cable it detects as slave.But make sure that otehr device is not set as master only 1 device is set as master or slave .
Let me know if you need further assistance.
Thanks for using FixYa.

Jun 01, 2010 | Seagate U6 (ST340810A) 40 GB Hard Drive

2 Answers

Need IDE jumber settings.


There is a little jumper block on the rear of a DVD. by IDE connector. on the case above there will be a Table marked . Master: Slave: CS. Now, you must set the jumper as to your drive's position. IE: Master or Slave, Master is on the plug at the END of the ribbon, the Slave is on the "Other" one. Accordingly the Master has the Master Jumper ON, the Slave the Slave Jumper ON. CS is Cable Select. It isn't all that used.

Feb 11, 2010 | Plextor 52x32x52 PX-230A Internal CD-RW...

1 Answer

Install old maxtor HD on newer pc, change it from mster to slave


From your own description Slave : Off therefore remove the jumpers

Jul 26, 2009 | Computers & Internet

2 Answers

Configure hard disck to slave


you have a diagram on the hard drive that shows you where to install a small jumper tab.  Make sure you also remove the master jumper position.  Be careful

Apr 01, 2009 | Seagate Barracuda 7200.10 500 GB SATA Hard...

2 Answers

Can not find Jumper diagram on N256 Maxtor model 33073H3


Hello there soggytundra, here's your GEEK-steer ...

Despite your question being posted here 5 days ago, I'll presume you still (and if not, then someone else will) need the answer ...

Virtually all Maxtor drives adhere to the following general rules concerning jumper settings (at least up until now):

= MASTER (M): Insert jumper over the FIRST COMPLETE pair of VERTICAL pins.

Examples:
Xoo o oXooo Xooo
Xoooo Xooo Xooo

= CABE SELECT (CS): Insert jumper over the SECOND COMPLETE pair of VERTICAL pins.

Examples:
oXo o oXooo oXoo
oXooo Xooo oXoo

= SLAVE (S): Do NOT insert ANY jumpers (or at least NONE VERTICALLY, but you may HORIZONTALLY across the TOP row as simply a means of storing the jumper).

Examples:
ooo o ooooo oooo oooXX oooXX ooXX
ooooo oooo oooo ooooo oooo oooo

TIP: As a general rule, if you KNOW the role of the jumper capable device you're installing, it is better to NOT use Cable Select (CS). In this case you do, therefore it would be best to specifically designate the (33073H3) drive as (secondary) Slave [and your other (primary) drive as Master].

Good luck and GOD-speed. Please post back if you have any further questions, and/or just to let me (and others in similar need) know how well this steers to solution.

"Today's the best day of my life...and NOW you're part of it!"

Mar 28, 2009 | Maxtor Hard Drive

1 Answer

Slave harddrive jumper settings


usualy its just one jumper if no jumper on maxtors becomes slave. jumper on 50 is master. if u use cable select.. on same ide another device must also be cable select.
if one is master other is slave on same ide.

Jul 15, 2008 | Maxtor Hard Drive

1 Answer

Free driver schematics


Put the jumpers on both the drives to CS(cable selct) then the master will automatically be the one on the end of the ribbon cable and the slave will be the one on the middle connector of the ribbon.

Oct 06, 2007 | Dell Dimension 8250 PC Desktop

2 Answers

Master\Slave Jumpers


Should be a diagram on the drive telling you where to put the jumpers (Master, Slave, Cable Select). You might also check Maxtor's site - bet they have the diagram you need. winstephen

Jul 09, 2007 | Maxtor DiamondMax Plus 9 120 GB Hard Drive

Not finding what you are looking for?
Quantum Fireball Plus AS (QMP30000AS-A) 30 GB Hard Drive Logo

Related Topics:

782 people viewed this question

Ask a Question

Usually answered in minutes!

Top Quantum Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tape-Techie

Level 2 Expert

74 Answers

Jax Planet
Jax Planet

Level 2 Expert

921 Answers

Are you a Quantum Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...