Question about Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune MAH4000 Motor Conversion Kit Instructions

I got my new Motor Conversion Kit today through the mail but it didn't include the instruction sheet on how to install the new motor and board. Can't figure out how new wiring harness on the motor is supposed to connect to the control board. Anyone have a copy of the instruction sheet? The instruction sheet is Maytag Part #16022060.

Posted by on

  • 3 more comments 
  • ppost02 Feb 11, 2008

    ppost@cebridge.net

  • ppost02 Feb 11, 2008

    My model is MAH4000AWW.

    Posted under wrong area by mistake.

  • ppost02 Feb 11, 2008

    Uhhh, what you sent me doesn't help. I need to know how to install the new motor and board. I cannot see any place where the new wiring harness on the motor connects to the new board.

  • ppost02 Feb 11, 2008

    Ooops, sorry. Guess I should have read the email first, not just the attachment.

  • ppost02 Feb 12, 2008

    Thanks sooo much! Got it back together and haven't washed a load yet but seems to be working okay. I have never seen a plug connected to a circuit board that way before. Wished I would have taken other posters advice about the mounting bolt ... my thumb is sore but I finally got it in. Thanks again.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

I do please post your email here and i will send it to you

Posted on Feb 11, 2008

  • 2 more comments 
  • Gary Davd
    Gary Davd Feb 11, 2008

    one thing you have the model listed under a MAH5500 but you say you have aMAH 4400 what is the complete model # i see to diffrent versions here and want to get you the right one

  • Gary Davd
    Gary Davd Feb 12, 2008

    Check your email now

  • Gary Davd
    Gary Davd Feb 12, 2008

    Great Glad to Help

  • jim racine
    jim racine Apr 18, 2014

    Gary, can you send the instructions for mah3000aww to another_td@yahoo.com? The #'s on the instruction sheet for this model are 16022060 and 6 2727880. Thanks in advance.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model MAH4000, will not spin out, door lock will


Check if the "locked"or "door locked" light comes on. If it does not, you need to replace the wax motor in the door lock assembly and the machine control board, which is inside the control panel. The control board is expensive, so instead of buying the whole control board, if you're good in electronic repair and soldering, try checking ebay for the control board repair kit. Search for "MAYTAG NEPTUNE WASHER R11 Q6 REPAIR KIT". It has all instructions how to do the repair. Good luck!

May 12, 2010 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

MY MAYTAG NEPTUNE MAH4000 WILL NOT DRAIN OUT OR SPIN


Check if the "locked"or "door locked" light comes on. If it does not, you need to replace the wax motor in the door lock assembly and the machine control board, which is inside the control panel. The control board is expensive, so instead of buying the whole control board, if you're good in electronic repair and soldering, try checking ebay for the control board repair kit. Search for "MAYTAG NEPTUNE WASHER R11 Q6 REPAIR KIT". It has all instructions how to do the repair. Good luck!

Dec 10, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune MAH5500B Washing machine


Hello,

Usually, the LR or 'Locked Rotor' indicates a problem with the motor / motor control board or MBC. The MBC is located near the floor on the right side. See www.neptunehelp.com for disassembly photos. The original MCB's had a high failure rate so Maytag redesigned the MCB and the motor. The motor conversion kit is part number 12002039, which includes the new motor, MCB, harness and takes about an hour to install. You can inspect the MCB for either a blown 10 amp fuse or if you see components that are burnt or discolored. If either of these is the case then you will need the motor conversion kit.

In addition, as your Neptune ages you might notice the spin cycle getting louder to where it will sound like a jet plane taking off. If this is the case then you can replace your bearings and seal kit. See www.neptunebearing.com. You can also rent a special Neptune bearing tool called the tony tool which includes the use of a DVD that shows you how to take apart Neptune, replace bearings and install the 12002022 seal kit. I hope this helps...

Jan 17, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

MayTag Neptune to Propane


buy the lp conversion kit from one off the links here at fixya and it comes with instructions

Jan 01, 2009 | Maytag Neptune MDG9700A Gas Dryer

1 Answer

MayTag Neptune to Propane


go to sears.com to get the conversion kit which will contain detailed instructions.

Jan 01, 2009 | Maytag Neptune MDG9700A Gas Dryer

1 Answer

Maytag Neptune


Check out the motor control board near the floor on the right side. These have a high failure rate on the Neptunes. Maytag redesigned both the motor and motor control board to be more reliable. While inspecting this board, you are looking for a blown 10 amp fuse and /or burnt components. If you have either... then you will need the the new motor conversion kit which includes the motor, motor control board and the wire harness.

See www.neptunewaxmotor.com for disassembly photos and other Neptune information.



Sep 04, 2008 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

I press the start button, it starts to fill then shuts off after a few seconds. If I go to drain cycle, I press the start button, it begins to drain the shuts off after a few seconds. No noises or...


Check out the motor control board near the floor on the right side. These have a high failure rate on the Neptunes. Maytag redesigned both the motor and motor control board to be more reliable. While inspecting this board, you are looking for a blown 10 amp fuse and /or burnt components. If you have either... then you will need the the new motor conversion kit which includes the motor, motor control board and the wire harness. This kit takes about an hour to install. See www.neptunewaxmotor.com for step by step pictures on how to disassemble your Neptune.

Jul 03, 2008 | Maytag Washing Machines

1 Answer

Need instructions for motor conversion kit for maytag neptune mah300aww


they come within the package when you recieve the conversion kit
.. if not contact where ever you purchased it and have them get to you

Apr 02, 2008 | Washing Machines

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

810 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...