Question about Philips Magnavox 20MC4304 20 in. TV/VCR/DVD Combo

1 Answer

Not this one magnvox mwd2202

This disc side wont open,,why> it wont switch to dvd,when u try is switchs right back to vcr?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Unplug it for a few seconds. I had the same problem and that is what worked for me.

Posted on Apr 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My toshiba dvd/vcr combo suddenly wont read dvd disc


Maybe the lasers ok but the disc motor is not spinning the disc.

Apr 28, 2014 | Combination Televisions

1 Answer

I have an Orion FTDV2004A tv/vcr/dvd combo. I was playing a DVD movie. When I paused it, it would not start playing again. Now, every DVD I put in, says "reading" and then "incorrect...


Hello
Just power OFF the set by its main power OFF switch, and switch in ON, while listening very close to its mechanism side and see whether there is any sound of disc spin. If disc do not spin inside the mechanism, due to a faulty sled motor, the fault you descrbes here will occur. If disc spins inside, and still it does not reads the disc, the laser pickup unit is faulty and should be replaced. OK.

Nov 06, 2011 | Orion FTDV2004 20 in. TV/VCR/DVD Combo

1 Answer

I have an Orien FTDV2004A tv/vcr/dvd combo. I was playing a DVD movie. When I paused it, it would not start playing again. Now, every DVD I put in, says "reading" and then "incorrect...


Hello
Just unplug the TV from AC mains wall socket, and replug into after 5 minutes or so. This should reset the set to its factory settings. If it does not help you, just take out the disc inside, and insert an other one. See whether it reads it or not. If not, the set need service. Especially service to its DVD mechanical side. OK.

Nov 06, 2011 | Orion FTDV2004 20 in. TV/VCR/DVD Combo

1 Answer

Dvd tray will not open


Had same problem. Unscrew back TV. Unscrew 2 screws connecting VCR/DVD from TV Base. Unscrew DVD housing on all sides (approx 6 screws). At this point you can see the detached DVD unit. Facing the draw. look under it for a white plastic piece that you can slide to the right that should disengage the DVD's circular rotator from the dvd and slide the door open.

If that does not work disconnect the DVD from the 2 wire connector at the TV motherboard and dissassemble the black plastic DVD unit. Flip it over and manipulate the white plastic gear which will disengage the center rotator.

Sep 08, 2010 | Toshiba MW24FN1 24 in. TV/VCR/DVD Combo

1 Answer

Toshiba TV/VCR/DVD combo (MW20F51) won't read/play dvds.


this a laser unit dirty or dead, needs to be cleaned with a laser cleaner kit or replace the laser unit

Feb 19, 2010 | Combination Televisions

1 Answer

Tape wont eject


Veri8fy that the belt on the side of the VCR mechanism is intact. If it is, then check that the motor works, by appying 12 volts to it,with the belt disconnected. If the motor works, it might be that your mode switch needs cleaning, and that takes some fancy unsoldering and soldering.

Sep 06, 2008 | Symphonic WF-719 19 in. TV/VCR/DVD Combo

1 Answer

Sylvanis tv vcr dvd combo


It sounds like the VCR mode switch is dirty. This is located on the PCB, underneath the right hand side of the VCR mechanism. If you do not know what you are doing, I do not recommend trying to clean it yourself. You have to remove the VCR from the board, and pop the wheel off the top of the switch. Use a cotton swab with a bit of alcohol to clean it, and then put a dab of WD-40 on it. Good luck. Also, you might want to tryt to reset the VCR mechanism to the fully ejected position if it is not there already.

Sep 05, 2008 | Sylvania 6727FDE 27 in. TV/VCR/DVD Combo

4 Answers

Bush Video Dvd combo Dvrhs02 Lock Code


Turn the unit on then press the 'vcr/dvd' and 'disc menu' buttons on the unit together and hold down until the unit reboots

Jan 03, 2008 | Bush DVD142RC 14 in. TV/DVD Combo

1 Answer

DVD PLAYS GREAT, TV AND VCR PLAY IN BLK-WHT W/NO SOUND


You have your DVD connected to your VCR, which is then connected to your TV, right? The problem is Macrovision. It's designed to prevent you from connecting your DVD player to your VCR, so that you can't make duplicates of copyrighted movies. It's a real pain in the neck. Try turning the DVD player off - or better yet, unplugging its power cord (as some DVD players are always in a standby mode, even when turned off). If that fixes the problem, then you need to reconnect your DVD player directly to the TV, not wired through the VCR. If your DVD player isn't wired through the VCR, are you using some kind of wire splitter (one cable branches into two) to connect both the DVD player and VCR? That can also cause this kind of interference, if both have power at the same time. There are video switches you can get to work around that. Here's one such switch (first I found for a decent price with a google search): http://www.pickeasy.com/20070827-video-selector-switch-video-game-p-555.html Hope that helps.

Aug 30, 2007 | RCA 27F500TDV 27 in. TV/VCR/DVD Combo

1 Answer

Unable to open my DVD player


i have same problem with vcr , all mecahnism ok but dvd ok but vcr does not work all mechanism ok beccause i check manul its and are ok let me know if you knw somethins , in your case chech manual it open the dvd internal and check for work manual . wilfred

May 27, 2007 | Panasonic PV-DR2714 27 in. TV/VCR/DVR...

Not finding what you are looking for?
Philips Magnavox 20MC4304 20 in. TV/VCR/DVD Combo Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Combination Televisions Experts

The Knight
The Knight

Level 3 Expert

68227 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Philips Combination Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...