Question about Whirlpool GEW9250 Electric Dryer

1 Answer

Want to dry plastic help please no joke

From montin view plastic's

Posted by on

  • 1 more comment 
  • Gary Davd
    Gary Davd May 11, 2010

    You can dry what you like but plastics and dryer go togeather like drinking and driving !!!

  • Gary Davd
    Gary Davd May 11, 2010

    Are you looking for a Dryer Rack??

  • robert samples May 11, 2010

    exactly what is your problem

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

Use a hair dryer . keever

Posted on Mar 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The tumble dryer is working perfectly and is vented through the external wall with a plastic hose , however the dryer is producing high moisture levels we have checked the connection fro the dryer to the...


Your problem is probably a heavy lint build up in the Dryer or Hose.

Check your blower system on the dryer for a heavy lint build up, also remove to clean or vaccum or whatever is necessary to clean the plastic tubing because they will still flow some air, but be really plugged up with lint and could cause a dryer fire.
This is a free answer, Please rate me

Apr 11, 2011 | Dryers

1 Answer

Need trouble shooting proceedure to enter self diagnostics for maytag neptune


From the service manual there is more to it but that was all I could put here.
Accessing Service/Diagnostic Mode:
Pressing down the damp dry and time (-) keys
for 5 seconds places the machine in the
diagnostic mode.
SPECIAL TESTS
The following table lists the various tests
available while in the Service Mode, which
can be accessed by pressing the following
keys:
Press Keys Special Test/ Function
wrinkle
release Diagnostic Codes
dryer
temp(^ )
Sequences up the
help/diagnostic code list
dryer temp(v) Sequences down the
help/diagnostic code list
time (-) Displays Software Revision
Number
very dry(< ) View current cycle
temperature (Co)
start/pause
Start or pause cycle running
but remain in Diagnostic
mode
Accessing Diagnostic Codes
After the machine is in the diagnostic mode,
a ‘d’ will display and let the technician know
they are in the diagnostic mode. Pressing the
wrinkle release key will access the diagnostic
codes.The diagnostic codes can be viewed by
using the temperature (^) & (v) keys.
The down arrow key will sequence down the
list one each time it is pushed with no wrap.
The first time the down arrow key is pushed
the display will sequence to the next code
logged. The last code being displayed being
the oldest code. The up arrow will sequence
up the list one code each time it is pushed
until it reaches the top code. If there are no
diagnostic codes available, ‘00‘ will be
displayed for the diagnostic code.
There will be no multiple occurrences of
either a diagnostic code or help code generated
in the same cycle reported on the list.
But if the same code occurs in repeated
cycles, it will be registered.
To clear the diagnostic code list press
wrinkle prevent and very dry (>) for 5
seconds while viewing the list.
System Check Mode
While in diagnostic mode, pressing the damp
dry
and signal (+) keys for 2 seconds, will
put the dryer into the system check mode.
"SC" will display.
This mode will allow the various inputs and
outputs to be controlled and viewed by the
technician by pressing individual keys. If no
activity is seen for 5 minutes after a key is
depressed, the control will reset back to the
normal mode. If no further activity is seen
after an additional 5 minutes the washer will
turn off. The following table lists the various
functions based upon on keys being depressed.
Membrane Pad Check
While in system check mode, pressing the
damp dry and sensor dry keys for 5 seconds,
will start a membrane pad switch test.
The membrane check involves turning all the
embedded LED on the membrane pad on.
All the LED’s can be toggled off by pressing
the key associated with the LED. To exit the
test at any point, press the damp dry (>) &
sensor dry keys again for 5 seconds or press
the off key to exit diagnostic mode.
Key Pressed: Function Performed
sensor dry
Enable sensor dry circuit.
(sense dry LED) When short
circuit is detected across the
sensor bars the normal dry
LED will turn on.
start/ pause
Cycles the motor relay
on/off. When the motor is
running the start/pause LED
is on.
dry temp(^ )
If motor is running, cycles
the heater/gas valve on/off.
When the heater is regular
temp LED is on.
very dry(< ) View current cycle
temperature (Co)
www.appliancehelponline.com

Mar 26, 2010 | Maytag Neptune MDG5500AW Gas Dryer

2 Answers

The dryer is not drying the clothes. It takes two


Take you vent off and remove the restrictions. How about a few repair pix?

Sep 25, 2009 | GE Profile Prodigy DPSR513GA Dryer

1 Answer

How do I know which thermal unit is the one that shuts the dryer off when the clothes are dry? one's called a cycling thermostat, another is called a fixed thermostat and the third is called thermal...


Usually the Fixed Thermostat (also known as the High Limit Thermostat) and Thermal Cut-Out (TCO) are used in conjunction to regulate and protect the heating circuits.

The Cycling Thermostat (also know as the Internal Bias) controls the amount of heat required/desired to dry your clothes.

You need to remove the rear panel of the dryer to access the heating circuits on this model dryer. With the back panel removed, the heating circuits will be on the right hand side and the blower fan assembly is located on the left. The Hi-Limit Thermostat and TCO are located on the outside of the heater box with the Hi-Limit Thermostat mounted next to the heating element terminals and the TCO located at the opposite end of the heater box. The Cycling Thermostat is located on the blower fan housing next the Thermal Fuse. It will be the metallic round component, while the Termal Fuse will be a white plastic component.

For better clarification, you can view an exploded view diagram of your appliance at pcappliancerepair.com. If you type in your model number, all the parts I've mentioned are listed under Section 3 (Bulkhead Parts). The components are listed as follows:

Item 6 - TCO/Hi-Limit Thermostat Kit (both parts should be replaced at the same time).
Item 15 - Hi-Limit Thermostat (sold separately)
Item 23 - Thermal Fuse
Item 24 - Cycling (Internal Bias) Thermostat

If you are experiencing heating problems or longer dry times, please review the following link:

http://www.fixya.com/support/r630242-dryer_runs_but_not_heat

Pay particular attention to the section that discusses dryer ventilation. The majority of dryer heat related problems and failures are attributed to poorly installed, clogged, or kinked dryer ventilation. If you haven't had the ducting checked in a while, now may be a good time to do so.

If you have any questions, or require additional assistance, please let me know. I hope this helps you.

Sep 10, 2009 | Roper REX4634KQ Electric Dryer

1 Answer

Help my dryer makes an awful squeaking noise when I dry . Maybe a loose belt not really sure. Do you have any ideas it still dries just sounds terrible doing it. Thanks Donna


The problem may not be the rear bearing. It could be the drum glides in the front drum bearing that the drum rubs against as it spins. The rear part of the drum is supported by the drum bearing. The front, however is supported by the drum glides. These glides are plastic and do wear down. Once they wear through, you usually have have metal on metal scraping as the front of the drum will be rubbing against the case of the dryer. You can view the glides at appliancepartspros.com. Type in your model number as "DBXR463EB0WW" The digit before the last two W's is a zero, not an "O". Go to the "Front Panel and Door" heading and locate items 313 and 316. This is the entire front bearing with glides. If the bearing itself is not worn, just replace the glides (take note of the glide color, there are different part numbers for them). You will need to lift the top panel, to access.

If you inspect the glides and they aren't worn, or if the noise you are experiencing is definitely coming from the rear bearing, you will need to remove the front panel of the dryer to access the drum. Once the front panel has been removed, you will need to release the tension on the dryer belt and remove it from the drive motor. Then, with the belt still wrapped around the drum you can use it as a handle to help guide the drum from its rear mount. A replacement kit is located under the "Drum" heading as item 508 (Includes all the parts).

Ideally, you hope that this is a simple drum glide problem. The repair isn't that difficult. Replacing the rear bearing, however, can be extensive for someone that has never performed this repair before. Take note of the exploded view diagrams for reference. NOTE: If you decide to repair this yourself, make sure the dryer is UNPLUGGED any time you service it. Dangerous voltage is still present inside the dryer, even with the power turned off.

If you have any questions, please let me know. I hope this helps you.

Aug 11, 2009 | Dryers

1 Answer

Clothes getting stuck in door seal when drying.


the plastic that you see overlapping the metal on the sides of the opening is in two parts, top and bottom, you can see the seem. the top is the smaller part, this plastic is also the drum support on the front. There are some glides on the top section that wear with time, after a few years they may need replacement. Perhaps these are worn out dropping the drum creating an uneven gap and catching. there is also a felt strip in there between the front of the dryer and the drum, keeping it back.
To view this remove the top by removing the 2 screws inside upper door opening holding top down. then lift top and if plastic console slide to left then pull away, metal -just pull straight. remove 2 screws holding front to cabinet sides. pull front forward. glides are visible on top. if not there or worn thru plastic replace upper plastic support

May 05, 2009 | GE DBXR463EDWW Electric Dryer

1 Answer

Kenmore dryer will not dry completelt in even heat cycle


This video will help you to determined what you need,
copy n paste
http://www.youtube.com/watch?v=HRKIU4LiS20&feature=related

for parts n prices
http://www.partselect.com/AppliancePartList.aspx?Brand=Kenmore&Appliance=Dryer&ModelNum=&Type=Electrical%20Parts,%20%20No%20Heating%20Elements&MinSize=U&MaxSize=U&Electrical=Y&Metal=U&Plastic=U&OneColor=U&PageSize=15&FirstPart=1

Was this helpful?

Apr 29, 2009 | Kenmore 63942 Dryer

1 Answer

Dryer wont dry


LONG dry time is an indication of a clogged or restricted exhaust. Clogged or restricted exhaust is the primary cause of failure in all residential dryers. Blowing the the system with a shop vac is only a temporary solution. The system needs to be cleaned (2 to 3 times per year) with a rotary brush to scrape lint collecting from the sides of the pipe. Suggest going to Lowes and purchasing vent cleaning kit. Read instructions CAREFULLY. Also consider replacing flexible plastic or foil pipe with rigid metal type. Dryer will vent 30% to 40% better. If condition persists for too long, a high limit fuse mounted on the heater will open causing the heater to no longer operate.

May 30, 2008 | Kenmore Dryers

1 Answer

Too long to dry my clothes


LONG dry time is an indication of a clogged or restricted exhaust. Clogged or restricted exhaust is the primary cause of failure in all residential dryers. Blowing the the system with a shop vac is only a temporary solution. The system needs to be cleaned (2 to 3 times per year) with a rotary brush to scrape lint collecting from the sides of the pipe. Suggest going to Lowes and purchasing vent cleaning kit. Read instructions CAREFULLY. Also consider replacing flexible plastic or foil pipe with rigid metal type. Dryer will vent 30% to 40% better. If condition persists for too long, a high limit fuse mounted on the heater will open causing the heater to no longer operate.

May 03, 2008 | Maytag Neptune MDG5500AW Gas Dryer

Not finding what you are looking for?
Whirlpool GEW9250 Electric Dryer Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...