Question about Maytag Neptune MAH6700A Front Load Washer

2 Answers

Help!! My maytag neptune MAH6700AWW is having trouble.

I keep getting NF and LE errors in between my wash cycle and rinse, and the rinse and spin. I have noticed that when my washer is filling that there is water coming out my drain house.... is my washer not filling, what do i do? Help Please

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I keep getting nf

Posted on Feb 19, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The fix was simple i just had to lift my drain hose off the floor. it had become disconnected from the back of the washer and was lying on the floor. I didn't realize that by it lying on the floor it didn't provide the proper back pressure to keep the water in while filling the tub. this was the NF error. as for the LE error. i haven't gotten it since i took off my cold water hose connection and ran hot water into it to losen the dirt/rust that was caked into the screen that is located in it. My washer is running like it is brand new again.

Posted on Feb 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We replaced pump on our Maytag neptune MAh6700AWW but we still got a nd code and it din't go into spin cycle?


cdmcdm5, did you ever figure out the solution to this problem? I currently have same issue. Have checked for obstructions multiple times and also ended up replacing pump. Still have same ND (no drain) code issue.

Jul 10, 2012 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Maytag Neptune Washer Problem


replace the door latch wax motor and check the drain pump for obstructions.

Jun 25, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune TL


The machine needs to cut you a break;

“”i have a maytag neptune TL and there are several things wrong with it...1. I can't wash small loads it will stop at the spin cycle and flash dc””

This issue is a clutch issue see this post to DIY the repair.

“”it will wash fine on regular loads until it comes to spin cycle again and it will stop and flash nf””

This one is a little confusing the “nf” error is a No water fill error code. Check these two post for support regarding water inlet restriction or valve not opening properly.

nf post nf post 2

“”my fabric softener dispenser will not let the softener out neither will the bleach dispenser””

See this fabric softer post for support. The fabric softener dispenser may be clogged or the water dispenser valves feeding both dispensers may not be operating properly. The Service Manual on page 16 “Board Output Test” will give you support to turn on the Fabric Softener Valve and Bleach valve. See if you hear the valves operate in Service Mode”

My method may seem a little confusion for viewing water flow to the dispensers. This issue could be associated to the nf error you are receiving, restricted water flow (inlet screen clog) or cold water valve not working properly.

Post back for any questions or possible support I can offer. I’m an owner like you not a repair person but I’m very comfortable working on this machine. Rich

Jun 17, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag MAH6700AWW Humming Sound


Can you see water in the drum ?,No water = no action Check water supply

If there is water in the drum does it drain out at some point.

Sequence = Fill, Agitate, Heat, Wash, Drain, Spin etc.

If it fills then it may be a belt has snapped and the drum cannot turn , need to take the covers off to look.

Remove power before taking covers off !!!!

If the belt is OK then it may be the heater which has gone open circuit, try a cold wash or a rinse cycle to test that.

May 23, 2009 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Machine keeps tumbling after wash cycle is completed.


Make sure that the replacement R11 is in fact connected to pins 1 & 2 of the Q6 triac. If the copper trace on the backside is open on either leg of the R11 to the Q6 then the wax motor will stay energized and that will cause the tumbling after the wash cycle.

See www.neptunehelpsong.com for a new funny song that explains the Maytag Neptune door latch wax motor issue.

Jan 21, 2009 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Maytag neptune mah8700. Will spin at the end of quick rinse cycle but not on any other cycle. Error code I get is SUSP. Washer does drain out.


Hi
My name is Gloria, my neptune washer will not spin on the last spin cycle of any of the washing cycle. A code of uC comes up.

Aug 08, 2008 | Maytag Washing Machines

1 Answer

MAYTAG PREFORMA 2 SPEED 10 CYCLES 2004 TOP LOADER


Check your lid switch, some machines stay running when you add clothes when it agitates, but will shut off if you lift the lid in rinse and spin, lid switch may be broken.

Jul 15, 2008 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Maytag neptune washer


Since I haven't heard back on this in over a week, I will assume it's been resolved with the clarification questions.

Jul 04, 2008 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Maytag Neptune Top Load Washer - Rinse Cycle won't run - Machine says nF


Sounds like the 'Wash water' is not pumping out fully,You need to drain the water by lowering the empty hose into a bowl & check the pump for a blockage ( if the pump is an 'electric one' check that it is working). TURN POWER OFF FIRST

Oct 25, 2007 | Washing Machines

Not finding what you are looking for?
Maytag Neptune MAH6700A Front Load Washer Logo

1,226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...