Question about RCA Universal Remote Control

3 Answers

RCU410wms RCA Remote

I have lost the instructions to this remote. I am trying to program a 15 year old Mitsibishi TV. I have tried the codes listed on other websites, but noting seems to work. What should I try?

Posted by on


3 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

This site will give you the codes;
Enter the codes 1> Press Hold Code Search until light stays on
2> press device button ie.TV
3>enter 3 digit code from site
4>Try Power button, if works great if not try another code
That's It!

Posted on Jan 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 547 Answers

I've got this remote, and the instructions. The "Code Search" function will get you there, but it's tedious.
Step 1: press and release the "TV" button (top right corner)
Step 2: Press and hold the "Code Search" button (small triangle directly below the on/off button) for 4 seconds until the red LED lights up
Step 3: Point the remote at the TV and press the on/off button slowly -- here's the tedious part -- for up to 200 times. Each time you press the button, it tries a different remote code.
Step 4: When the TV turns on for you, press the "Enter" button (right side, just above the channel/volume keys)
Step 5: You're all set!

Or, if you're like me, there's a step 3a: press the on/off button to quickly, and hit blow right past your TV's code before you notice. If you do this, hit "Enter" and start over, going more slowly this time.

Good luck!

Posted on Feb 11, 2008

  • 1 more comment 
  • Rob C Feb 11, 2008

    The user's guide is available online:

  • Rob C Feb 11, 2008

    The manual is online here

  • TtheTA May 18, 2011

    Inistructions are not exactly right. After Step 2 above, you have to push the "TV" button again, then proceed to step 3 above.


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 259 Answers

Here are the instructions to program your remote: Introduction It takes just a few steps to program an RCA Universal Remote Control using the Automatic Code Search method. While there may be some trial and error, the pleasure of getting rid of several extra remote controls will far outweigh the hassle in getting it programmed. Instructions Difficulty: Easy Things You'll Need

  • RCA Universal Remote Control
Steps 1 Step One Turn on the component you want to program. 2 Step Two Press and release the component button on your remote that corresponds to the component you want the remote to operate (TV, VCR, etc.). The illuminated ON-OFF button will turn on and remain on. 3 Step Three Press both the component and the ON-OFF buttons. The illuminated ON-OFF button will turn off, and then will come back on. 4 Step Four Release both buttons after the ON-OFF button turns back on. The button should remain illuminated. 5 Step Five Press and release the PLAY button. If the component does not respond after five seconds, continue to press the PLAY button every five seconds until the component turns off. 6 Step Six Press and release the REVERSE button when the component turns off, then wait to see if the component turns on again. 7 Step Seven Press and release the STOP button to save the new code.

Posted on Feb 10, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Code for Toshiba TV on rca universal remote

there are many different codes, here is a link to a site with some of them, scroll down to your brand of TV, there will be a list or # codes. In the past when I programed my remotes to my TV's, sometimes there were no matches for my TV on the list. if non of them work, in the instructions for your remote there is a procedure that you go through to program a unit if you don't know the code.
if you lost your instructions for your rca universal remote go here to watch short instruction video

Aug 18, 2014 | Televison & Video

1 Answer

Lost the code list for my rcu404N universal remote an trying o program a rca television

With the information you've provided, I found the following link to the manufacturer's website for the remote. The codes are listed below for a standard RCA television.,-user-manual,-code-list-and-support-for-the-rcu404n-remote-control RCA .............1547, 1447, 0047, 0090, 0679, 1047, 1147, 1247, 1347, 1781, 1948,1953, 1958, 2002, 2187, 2247 I've included the step by step instructions provided by the manufacturer for programming your remote to operate your TV. If you need other devices programmed, check the link to download the original instructions on your universal remote. Hope this helps.

Feb 22, 2012 | RCA Universal Remote Control

1 Answer


The code list is located at the following website:
Find your TV and hold the TV button on the top left. While holding the TV button, enter in a 4 digit code (they should be in the 1000's) - then release the TV button and try the channels or volume up or down
EXAMPLE: TV(1047) release TV button
- try all 4 digit codes associated with your TV
- once the code is entered, try it by clicking channel up or down
- hope this helps, this can be frustrating
- If the remote responds, stop trying codes, your remote is programmed

Feb 06, 2010 | RCA 4-in-1 Universal Remote Control

1 Answer

I have this RCA Universal remote (RCU410WMS) and I am trying to program it to use it on a Magnavox TB110MW9 DTV Digital to Analog Converter. I've tried the code search method and nothing. Anyone with a...

RCA's site list codes 25 and 006 for Magnavox cable boxes. Maybe one of these will work for the converter. The RCA site has a link so you can look up codes. Click on "find your remote control codes here" and pick your model number, then the type of device you want to control. If the codes I gave don't work, maybe try some of the other brands of cable box codes. You might find one that will work.

May 04, 2009 | RCA Universal Remote Control

2 Answers

I have a new RCR312W TV remote. I have lost directions

Someone had posted a solution to manually program the remote. The information came from RCA website. It worked fine. I still would like the code numbers for my remote. I have a LG TV that is about a year old.

Feb 14, 2009 | RCA Universal Remote Control

2 Answers

Programming my remote

Here is a link for the generic programing instructions for the RCA universal remotes. Scroll down the page for a list of device codes.
Let me know if this is what you were looking for.

Dec 28, 2008 | RCA RCR311B Remote Control

4 Answers

I need codes for a rca d770

Programming For TV
1. Turn on the device to be programmed.
2. Look up the brand and code number(s) for the device on
the code list at the end of this section.
3. On your remote control, press and hold the device button
you want to program.
4. Enter a code from the code list.
5. Release the device button, and then press ON•OFF to
see if the device responds to the remote control
commands. If it doesn’t, try pressing the device button
and then ON•OFF again.
6. If you get no response, repeat these steps using the next
code listed for your brand, until the device responds to
the remote control commands.

Emerson ..................1004, 1006, 1012, 1014, 1023
..................................1024, 1025, 1026, 1027, 1028
..................................1029, 1030, 1031, 1033, 1034
..................................1035, 1036, 1038, 1039, 1041
..................................1042, 1043, 1044, 1046, 1047
..................................1123, 1124, 1162, 1171, 1176
......................................................1177, 1179, 1191

Your user manual is available for download and option printing at the following link :

May 16, 2008 | RCA D770 Remote Control

3 Answers

Remote controls

have your problem fixed get a / one for all / remote controe it has the tv in that you have in the list cost little to nothing to get it go to wall mart please reply thanks p.s. rca dont have codes for that tv all for one does

Mar 28, 2008 | Durabrand DWT1905 TV

1 Answer

Program my new rcr remote.

Your RCA codes and instructions are at this RCA link:

Mar 26, 2008 | RCA Universal Remote Control

Not finding what you are looking for?
Televison & Video Logo

4,561 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74459 Answers

matt martin
matt martin

Level 3 Expert

1213 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides