Question about JVC RX-5030/32 Receiver

Open Question

Intermittent audio from Subwoofer Speaker

I purchased the JVC RX-5030 SN# 678X7020 Home entertainment center a few years ago. The problem I am having is that the subwoofer model# SP-PWA380 is going in out periodically. I have determined it is the subwoofer because I have subsituted one of my other subwoofers with it plays without going in and out. I would like to get the original subwoofer fixed that came with the system because it sounds so good together. Any suggestions?

Posted by on

  • fuckineh Apr 09, 2008

    I also have a JVC RX5030v With the subwoofer sxpw650v.2 that cuts out. Thought it was the TV cable reception, reciever seemed to work while watching dvds, but then started all the time. Have not tried other sub yet. whats the problem here?

×

6 Suggested Answers

  • 51 Answers

SOURCE: speaker wire for subwoofer

Usually, a subwoofer will have its own built-in power amplifier. Thus, it will be designed to plug into a standard RCA jack (the type used for DVD players, etc). rather than having wires to connect to a speaker terminal block. Look for a jack on the back of the receiver called "Subwoofer", or simply "SW". If your subwoofer has 2 single wires, it WON'T work with your reveiver's subwoofer output, as this output only carries a line-level signal and is not amplified. You would need a separate power amplifier for this type of SW. If your SW speaker has a DVD-type plug, it should work fine with the receiver's SW output jack.

Posted on Jan 02, 2009

  • 1 Answer

SOURCE: No Soound on Subwoofer from Yamaha RX-V363

I have the same setup. Are you going out of the subwoofer output of the reciever? (it's purple.) then into the LFE jack of the subwoofer (also purple.) That's the only connection you need besides power. If you have those right, try using your cable for something else to make sure the cable is good. Is the indicator of the subwoofer green? Mine comes on with the reciever. Good luck!

Posted on Apr 14, 2009

  • 231 Answers

SOURCE: can I hook the reciever to mm bose subwoofer and 5

if bose unit has built in amplifier .Then your sherwood would have to have a variable RCA output jacks in order to work with sub.Then bose audio input RCA cable would connect there.If bose unit does not have built in amp .Then you would connect sherwood left/right speaker outputs into bose left/right inputs .Then other bose speakers will connect to bose unit

Posted on Jul 30, 2009

  • 87 Answers

SOURCE: how to add a subwoofer?

Car systems and home systems are different in the fact that the car system expects to receive 12 volts DC for power, and they are usually 8 ohm speakers. I would not recommend doing this unless you are in the mood for some serious config. Power converter from 110 AC-12v DC and big enough to handle the amperage. If it's not powered, then your going to be running a 4 ohm speaker on an 8 ohm amp output. Again, not recommended.

Posted on Oct 25, 2009

  • 18 Answers

SOURCE: Subwoofer not working.... JVC surround sound

A connectivity check could provide the solution, notice any wrong wire connections on device or any other devices requiring interconnection. The woofer would perform properly when the connections that provide current for woofing are approapiate

important notes
1. Trace the connection from Recorder or sound output to the woofer device
2. The wiring connections should be sound and video ouput into sound and video output into woofer.
3. The connections if any problems would be located at the stereo recorder or device producing the spund and video. Check the connections of wires on the recorder device ensuring rewiriing
4. finally, adjust the equalisers if any the buttoms could have been disbled by master switch hindering full blaster boost sound.

Posted on Dec 05, 2010

dunnbiker
  • 8546 Answers

SOURCE: Yamaha Rx-V367 Subwoofer not working,

Have you looked at the manual?

The NEW thing doesn't work.

Does the subwoofer work for setup? That would certify the hardware and speaker definitions are ok.

The PC has the responsibility for defining and sending out something between headphone and full-blown 7.1 though the HDMI. Check your PC sound controls and the "Information on HDMI" section of the manual.

For the radio mode, probably the only analog stereo source you have, read up on the STRAIGHT decoding mode and Sound Field programs.

Posted on May 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear speakers are dead, never got them to work. Changed front to back and rears work so speakers and wireing are good. Is it possible that because I did not hook up a center speaker this is the problem?


if its a 5.1 channels it means 2 front speakers,2 rear speakers or either the center speaker or the subwoofer.try to hook up either center speaker or subwoofer.

Jun 05, 2010 | JVC RX-888V Receiver

1 Answer

How to add a subwoofer?


Car systems and home systems are different in the fact that the car system expects to receive 12 volts DC for power, and they are usually 8 ohm speakers. I would not recommend doing this unless you are in the mood for some serious config. Power converter from 110 AC-12v DC and big enough to handle the amperage. If it's not powered, then your going to be running a 4 ohm speaker on an 8 ohm amp output. Again, not recommended.

Oct 25, 2009 | JVC RX-717V

1 Answer

No sound out of subwoofer


Connection from receiver subwoofer output jack RCA plug male go into your powered subwoofer low level input with other end of cable, then you need to select Subwoofer YES/NO on the JVC receiver speaker setup menu option, select YES if this is a powered subwoofer you are using, should power up the subwoofer, may have to adjust a test tone balance for multi speaker output also, try trimming up on the subwoofer channel to initiate the signal on if the sub has an auto-on feature.

Feb 07, 2009 | JVC RX-5020VBK Receiver

1 Answer

Speaker wire for subwoofer


Usually, a subwoofer will have its own built-in power amplifier. Thus, it will be designed to plug into a standard RCA jack (the type used for DVD players, etc). rather than having wires to connect to a speaker terminal block. Look for a jack on the back of the receiver called "Subwoofer", or simply "SW". If your subwoofer has 2 single wires, it WON'T work with your reveiver's subwoofer output, as this output only carries a line-level signal and is not amplified. You would need a separate power amplifier for this type of SW. If your SW speaker has a DVD-type plug, it should work fine with the receiver's SW output jack.

Jan 02, 2009 | JVC RX-554V Receiver

1 Answer

Config Problems After Repair


Sounds like they centre has configured your speakers to "none". You need to hook it up to a tV or monitor and go through the menu to "speaker settings" and make sure you select either "sml" or "lrg" for the speaker type. Also ensure on the LFE settings that you select either "swoofr" or "both."

Nov 02, 2008 | Yamaha RX-V800 Receiver

1 Answer

RX-668V - Center Speaker Channel


have a tech check your set it is a bad cap that that bias a very small voltage to that circuit or it could be cold solder.good luck.

Apr 15, 2007 | JVC RX-668V Receiver

Not finding what you are looking for?
JVC RX-5030/32 Receiver Logo

Related Topics:

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Rod
Rod

Level 2 Expert

224 Answers

Are you a JVC Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...