Question about Maytag LAT2300 Top Load Washer

2 Answers

Water leaks (drips ) into tub after cycle/spin is complete

After completing a wash cycle ( thrugh the spin ), water continues to "drip" into the tub...for varying amounts of time - not extremely long ( but never actually timed the duration ). The machine is seven years old, but the problem has only occurred in the last two weeks ( since the last week in January, '08 ).

Posted by on

  • hibbingmn Feb 10, 2008

    Thanks...let me make sure that I get your drift; When you speak of "hose", do you mean the hose that goes from teh awter supply itself to the fitting on the washer, or do you mean a different 'hose' ( maybe something inside the washer's abck bulkhead ? )....

    Thanks again....

    Hibbingmn

  • Anonymous Mar 20, 2014

    ptwn6050mowt

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 871 Answers

Hi there

you can check the connection hose thats directly under the tank. it may be due to time and there may be a crack on the hose. you may readily buy a replacement hose from any malls in your area and you can actually do the replacing yourself. Doing the replacement requires you to tilt or completely flip over the machine to handle the changing of the hose with ease.

hope this helps

Posted on Feb 10, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 796 Answers

You have a bad pressure switch or the small hose connecting to the pressure switch may be bad

If the washer leaks water when is filling only, check the following: 1.Fill hoses
2.The water mixing valve

3.Filling injector ( If your washer uses one )
4.Filling spout


If the washing machine leaks during the wash cycle, check the following:
1.The pump
2.The tub stem & seal
3.Tub to pump hose
4.The drain hose
5.Tub (rusted holes)
6.The drum support bolts


If the washing machine leaks during the spin cycle, check the following:
1.The drain hose
2.The tub cover seal
3.The pump
4.The pump hoses

5.The stem & seal
6.The drum support bolts

Posted on Feb 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an MAV7600 Maytag washer the hot water fill valve drip after the cycle complates


if the washer keeps taking water and even when the washer is on the off position.
The problem could be a bad water valve.

Mar 15, 2012 | Maytag MAV7600 Top Load Washer

1 Answer

The water, there was no water left in the tub of the washer, but the clothes were dripping wet; and the cycle was showing to be complete. I had to re-set the dial to the spin setting inorder to completely...


What has happened is that your water pump has gone out and it cannot pump the water out of the washers tub. This is a common issue and replacing the pump is not that hard assuming you have the time, effort, tools and energy.

Jan 23, 2011 | Kenmore 24962 Top Load Washer

1 Answer

Water is continually leaking into the tub from the inlets as a slow drip. This happens while the washer is off and continues forever unless the water supply is turned off. This is a stackable washer/dryer.


A defect in the water-inlet valve may mean that it's no longer able to shut off completely when the electricity has been turned off to it. If this occurs, the valve may leak and drip water into the clothes tub. In time, the water may accumulate substantially. If this happens, you need to replace the valve.

Jan 06, 2011 | Washing Machines

1 Answer

Water continues to drip into the tub even after all cycles have completed. my tub is filling up with water, I have turned off the water to the machine but it continues.


The water inlet valve needs to be replaced. It's not shutting off the water completely. It's located where the water hoses connect to the washer.

Oct 09, 2010 | Maytag Washing Machines

1 Answer

After wash cycle is finished I lift the tub lid and water is dripping into tub.


You may be looking at residual water dripping down from the rim. If the drip is located near where the water fills from, then you may have a water valve (could be either hot or cold side) that is not able to close completely. The valves are typically replaced, but sometimes cleaning can help for short term. Consult your user manual for removal / replacement instructions.

Aug 18, 2010 | Maytag Washing Machines

1 Answer

Water drips in tub after washing is completed! kenmore 80 series


Check the solenoids at the water inlet valve. They can be tested using a multimeter or ohmmeter. Check for continuity. A lack of continuity indicates a faulty solenoid. I will attach a photo for reference. A bad solenoid will permit water to leak through to the tub. Hope this helped and best wishes.

908a1b9.gif

Aug 30, 2009 | Washing Machines

2 Answers

Leaking water


Does not sound like a bearing problem. Check to see if water is overflowing the top of the tub during spin cycle (due to spin action) and running down the side of the tub.  Water rising up the side of the tub during spin cycle could also be squirting up through bleach dispenser opening and running down side of tub.

May 30, 2009 | Washing Machines

1 Answer

Leak


Your inlet water valve where the fill hoses attach is stuck open.

Mar 18, 2009 | Washing Machines

1 Answer

Whirlpool washer continuouse water water runninng into tub


try turning the mach off while it is spinning and filling.if it continues to fill or drip heavy,the mixing valve is not closing completely and needs to be replaced.if the water stops when the mach is turned off,there is a problem with the pressure switch.

Sep 28, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Washer continues to drip into tub after cycle in complete.


contstant water dripping into tub sounds like a bad water valve, no repairing valve just replace it

Feb 25, 2008 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

629 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...