Question about 2wire (1000-400108-001) Router

1 Answer

Lights on my router there is only 2 lights on witch is power and broad band link is thta normal? and when my laptop connects to it is says (limited or no connectivity) so can u solve this 1?

Posted by on

  • Kevin Pettit
    Kevin Pettit May 11, 2010

    Have you run the setup wizard for 2Wire on the laptop?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No power light comes on when I connect my 2wire wireless device.

Posted on Feb 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

So I got a new router. Same brand as the old one (Netgear) I set everything up like normal. Everything connected. 2 Wii's, 2 androids, an iPhone, 2 desktops, and a laptop. The problem is even though...


I am assuming the you are trying to connect (and the problem is) wirelessly. Usually this happens when a laptop or desktop has been hooked up to another router. When switching routers you need to boot up hardwired to the router. This will allow the router to establish an IP address for the device. After this one time boot process you should be able to connect wirelessly.

May 15, 2011 | Routers

1 Answer

What ports do i plug into to be able to use a Broad Band internet


Hi,

Plug the lan cable from Modem to the Router Wan / Internet port. From Lan port ( Router) you can connect to switch or computer if you have any . Or connect computer via wireless.

That' all

Mar 25, 2011 | D-Link AirPlus Xtreme G DI-624 Wireless...

1 Answer

One of my friend in my neighborhood using netgear wifi router when i connect with that performance vise netgear seems 2 b better is thr any setting to enhance the performance .... we both r using airtel...


To enhance performance is to enhance signal strength which can be accomplished with a repeater or an ACCESS POINT router with detachable antenna.

THen you can connect an omnidirection or bidirectional antenna which will enhance the signal.

You can check TP-Link products. Their routers are with detachable antenna. They have a grid antenna which is like a bid dish for detecting signals.

God Bless You!

Feb 05, 2011 | Belkin (F5D7230-4) Router (587009)

1 Answer

Hi, my 2 wire ATT wireless broad band Internet router isn't working. Flashing red lights notes


You need to RESET router then configure it .For that press hold RESET button for 10 seconds then all settings defaults. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi . Let me know if you need further assistance. Thanks for using FixYa.

Sep 04, 2010 | AT&T Routers

2 Answers

How can i connect the router? i got a intellinet 192.168.1.1 there is one wan and 4 ports are there.i have dialog broad band connection.how can i connect it?or iwant to install any software?


This is very easy to do and you should have no problems doing this. The first step to installing it connecting your router to your broad band router through the wan port. All you do it take your Ethernet cable that went from your broad band router to your computer and attach it to your new routers WAN port. next wile your new router is turned off, turn off your broad band router and then turn it back on wile it is booting up turn on your new router this is not always necessary but it will make sure that they sink together properly. And that's it your done just hook up all of your other computers to the remaining ports and they should work with out a problem.

PS. this is just the basics of setting up your router if it has wireless you may want to think about implementing some security measures such as encryption.

I hope this helped.

Thank you,
Norse

May 18, 2010 | Intellinet Active Networking Intellinet...

3 Answers

I got the linksys router problem which no problem at all when i connected to sg broad band . currently use it to connect to malaysia streamys broad band and problem occured. when i connect the router to...


For that you enter in linksys configuration page with 192.68.1.1
then enable dhcp .
Aso set WAN settings as your internet service provider settings.
For that you have to set DNS server and other settings as your malaysia streamys broad band settings.
Let me know if you need further assistance.
Thanks.

Oct 28, 2009 | Linksys Wireless-G Broadband Router

1 Answer

Linksys router model WRT54GX2 SRX200 drops wireless connection on the laptop and the ethernet connection on the desktop. Connection drops for seconds then reconnects in seconds. By-passing the router and...


read on the router if its broad band , if is not , you will not be able to use it , so my advice to you is get aother linksys router with broad band on it .wish you all the best

Aug 04, 2009 | Linksys WRT54GX2 Wireless-G Broadband...

2 Answers

Linksys wirless G 2.4 broad band router download driver


Are you trying to set up router ?
You can set up your router manually, without the CD.
Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

Feb 10, 2009 | Linksys Wireless-G WRT54G Router

3 Answers

DSL link is not stable and unable to establish broad band connection.


I suggest you to do a hard reset on your router. Press the reset button at the back of the router for 20 seconds then unplug the power for 1 minute. Then reconfigure your PPPoE settings. On the Setup page of the router, make sure to choose the "Keep Alive" option.

Oct 18, 2008 | Linksys WAG200G Router

Not finding what you are looking for?
2wire (1000-400108-001) Router Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top 2wire Routers Experts

Bob S

Level 1 Expert

15 Answers

Justin
Justin

Level 3 Expert

2072 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a 2wire Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...