Question about Indesit W 123 Front Load Washer

1 Answer

W123 dispenser drawer keep melting

Hi
I have had my Indesit W123 for about 5 years now, and have had no bother with it up until now. On a 90 hot wash the front of the dispenser drawer melts and is now warped..... surely a machine that is designed to do 90 washes should be able to withstand the temperature of this wash.
What can i do? Or where can i get a new dispenser drawer from that is reasonably priced?
Thanks
Michala

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 417 Answers

Hi there you can order the part from indesit and should not cost alot and yes it should withstand the temp check that if you are using the hot tap to the machine turn down the water thermostat as maybe too hot.

Thanks J

Posted on Feb 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Leaking washing machine


Disconnect first the mains, power plug off the wall. You could have a clog in your soap drawer; pull the dispenser drawer completely out. There is a tab that needs to be depressed to release the drawer to remove. Clean the soap drawer with an old tooth brush. The usual block could be old soap, softener, etc. (you could also be using too much soap powder). I usually use just above 125ml (my measure cup says ml, I use front loader powder for the 5.5kg load) The wash is very gud. This is the normal issue that will cause water to leak out of the dispenser housing.


Wash the dispenser drawer thoroughly with warm water. Make sure that you pull off the siphon covers and wash all siphon holes. This process is described in your owner's manual. Next could be one of hoses has become loose, should be re-fixed. Examine by removing top of the front loader; this will give you a gud view of the pipes.


If helped, click.

Apr 14, 2013 | Indesit Washing Machines

1 Answer

Indesit w123. motor burnt out?


If your seeing flashes from behind the dial I'm thinking that the timer needs to be changed. Even with the motor shorted out, it still wouldn't cause that effect to happen.

Jun 17, 2012 | Indesit Door Handle Kit for W123, W133,...

1 Answer

Indesit wd10 water pouring out from powder compartment what is most likely cause?


Blocked siphon tube from conditioner segment or blocked hose from dispenser to drum. Pull dispenser drawer out and clean in the hole where it comes out from. Then regularly do a hot wash without using any detergent or conditioner

May 09, 2012 | General Washing Machines

1 Answer

I don't know how to operate it


Hi Sam

The user manual is available to download at the link below -

Indesit W123 User guide

Jan 30, 2011 | Indesit W 123 Front Load Washer

1 Answer

The fabric softener compartment of the detergent drawer is not emptying. The machine is an Indesit W123.



I have had my machine for the past 6 years, I do on average ten loads per week, and it has never failed me. A bit noisy but for the price I could n`t complain. I have just broken the door handle which has cost me a total of #8.50. Not bad for six years hard labour

Dec 04, 2009 | Indesit W 123 Front Load Washer

1 Answer

Water in softener compartment Indesit w101 (not above)


Go to Indesit web site download user guide
http://www.indesitservice.co.uk/hs/pages/manual/manualSearch.do

Most soap drawers have a plastic latch which needs to be pressed to release it.

You will find that there is a ball of soap congealed in the back of the dispenser drawer

May 25, 2009 | Indesit W 123 Front Load Washer

1 Answer

Replace door rubber W123


how do I replace the door rubber on Indesit W123

Oct 26, 2008 | Indesit Washing Machines

1 Answer

Indesit washer w123


take soap drawer out and clean it

Aug 28, 2008 | Indesit W 123 Front Load Washer

1 Answer

Dispenser issues


pull drawer out towards you, untill it comes to a stop.!push down plastic tab and pull the rest of the way out,some dispensers have to be lifted and pulled at the same time.wash it then with hot water! take apart softener compartment to clean,makeing sure small hole is free!!!close eire

Dec 15, 2007 | Frigidaire GLTF1670A Front Load Washer

1 Answer

Indesit w123


the holes above the drawer may be blocked. remove the drawer and scrub the holes with a stiff washing up brush rinse away then try again.

Jun 21, 2007 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

neilmoto

Level 2 Expert

75 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...