Type of dremel to use for computer case modding

First you need to get an equivalent charger and some type of male/female or contact harness. This will have to have at least three pins as that is what is already on the Dremel. Now the difficult decision, do you want to open up the Dremel if it's still under warranty? If you don't mind opening it then my solution will work. Open up the Dremel and look at the inside of the contacts. As this is a DC charger it can only have positive and negative terminals. You say there are three contacts, so there will either be two positive and one negative or two negative and one positive. Most likely there will be a bridge wire between the two terminals with the same polarity. Strip a little of the insulation from the terminal wires and solder new leads to your contact harness. Noting the polarity of each pin/contact on the new harness wire the other part of the contact harness to the charger. You will most likely have to make a small hole in the Dremel's outer cover to allow the wires to pass through. As you own a Dremel I'm sure you are capable of attempting this easy bit of DIY. There is only one problem, If the third contact plate is a return signal to the charging base it might be to inform the charger when the battery is full. In this case the terminals inside the Dremel will not be bridged and I suggest you buy a new or secondhand charger. Hope this helps

hello,

try to find it here:

http://www.powertoolspares.com/parts2.php?model_ID=3057

may this help.

melnavz

you can call them direct and buy parts at 1-800-437-3635 7AM to 6PM CT M-F. Let me know if you need more assistance

Hello, M8052895 -

I found a list of authorized Demel repair centers in the Philippines here:
http://www.dremel.com.ph/ph/en/service/after-sales-service/dremel-authorised-service-centre-list/

If you scroll down that page, you will find a Philippines contact telephone number.

Best wishes.

http://www.dremel.com/en-us/projectsandcommunity/projects/Pages/default.aspx

this website is directly from dremel. It shows different projects, crafts, or hobbies you can use it for. It is a real simple tool to use, and also is very handy. You can obtain several types of bits for it ones for sanding, engrving, cutting all types of materials, and much much more. Hope this helps

Hello. I'm new to FixYa and just found your inquiry.Dremel does have a router attachment for your unit. The model is "Dremel 335 - 01 Router Attachment" and usually sells for about $20-$30. Here's Dremel's cust assistance info just in case:
Phone:
1-800-437-3635 (toll free)
1-262-554-1390
(7am-6pm CT Mon-Fri)

My friend ... my first inclination is to say 'Are you kidding me?' My Craftsman 'skill' saw with 7 inch blade has its hands full ripping 3 feet of 1/2 thick mahogany and you are using what is essentially a hobby tool and you question is will it over heat? You are lucky it didn't burst into flame!

I don't know if this particular model is thermo protected or not. If it comes back on, we can guess there is a device inside to protect it. If not, it is probably taps for the Dremel.

While the Dremmel is a wonderful tool it is not intened for this kind of work. My fear is you have burned it up. I use my Dremel saw to cut pine and balsa for modeling, (cars, boats, planes) and other little projects. I use the little sanding drums for the same, as well as polishing. The little rasps are great for cleaning and cutting. Not intended to rip lumber for a furniture project.

I'm sorry your Dremmel met a early demise and I hope I have answered your question. Please do not kill the messenger. Thank you for your interest in FixYa.com

hello. yes. go to dremel.com and get new brushes for your tool.
ps kindly rate my answer as helpful. thank you. Joe

If this is Dremel go to Dremel.com and you can download an owners manual or call toll free and speak with one of their tech guys to help you get started.

You can call Dremel direct at 1-800-437-3635 and order the part. Let me know if you need more information.