An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert who has written 50 answers of more than 400 characters.
An expert whose answer got voted for 20 times.
Re: tray 1 - load ltr (WHAT DOES THIS MEAN!!!)
Hope this helps. Please check the printer properties before clicking Ok at print menu command. Now check the available paper tray handler. Try bypass, tray1 or MP tray.
Check also the default paper on Printer Menu command by pressing appropriate setup button. You can try also placing the paper on bypass try if available. The load LTR message means the machine waits a short bond paper on MP tray or on bypass tray.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
This means that your machine has received a print job that is teling it to print on paper that is loaded or supposed to be loaded in the bypass feed tray. You will either need to delete the print job using the operation panel or simple load some letter size paper in the bypass tray over on the right side of the machine.
Good Luck and Thank You for using Fixya.
This is usually caused by the tray being incorrectly adjusted.
First remove the paper and check for curls on the end that was facing the rear of the tray. If the paper has curled, it was pushed too far into the tray.
There is a small tab inside the tray at the front that should be aligned with a mark that says "Ltr or Letter". There should actually be a little arrow on the tab pointing to an alignment mark what should say "Ltr or Letter". If it is pointed at something else, squeeze it to move it to the "Ltr" mark Once done, the paper should fit loosely in the tray without curling at either end.
Please note. SOME of these models have a tray that adjusts differently. In these models you can actually make the tray a little bigger by pulling it lengthwise. Consult your owners manual or down-load it from brother.com if you are unsure. In either case there will be two marks in the tray that you must line up correctly to make sure the tray is set for the correct size of paper. The marks should have LTR or Letter written beside one of them. If the tray is set too small it will jam the paper up into the feed slot. If the tray is set too large, the paper may not reach the pickup roller causing a "paper out" error. The paper should sit loosely in the tray with no more than 1/4 inch of space at each end of the paper.
Also make sure your paper is not stuck together with static. It helps to "fan" the paper like a deck of cards before putting it into the tray.
Hi, Hope this helps. Please check the printer properties before clicking Ok at print menu command. Now check the available paper tray handler. Try bypass, tray1 or MP tray. Check also the default paper on Printer Menu command by pressing appropriate setup button. You can try also placing the paper on bypass try if available. The load LTR message means the machine waits a short bond paper on MP tray or on bypass tray.
Check the paper size setting in the printer. Set it to the paper size you normally use such as A4 and the default tray. Check the default paper size in the printer driver in your computer and the default tray. Finally, check the paper size of the document you are printing. If all these match, it should not try to be smart and ask you to feed paper.
LED pattern Possible Problems and Solutions Your system has some problems. If this problem occurs, contact your service representative. On Line/Error LED lights red • Paper jam occurs. To solve the problem, see “Clearing Paper Jams” on page 5.6. • The front cover is open. Close the front cover. • Paper tray is empty. Load the paper in the Tray. • The toner cartridge is out of toner. Remove the old toner cartridge and install a new one. See “Installing the Toner Cartridge” on page 2.4. • You pressed the Cancel button while the printer is receiving data. • In Manual Feed mode, there is no paper in the manual tray. Load paper into the manual tray. • If the printer is receiving data, the On Line/Error LED slowly blinks green. • If the printer is printing the received data, the On Line/ Error LED blinks green fast.