Question about Speakers & Subwoofers

1 Answer

Jvc rx-552 v

Sound cut out when turned up past 2. why?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Cut the bass down and see if that helps

Posted on Feb 07, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jvc rx 703b repair--I was playing on a technic sl mk2 turntable made a loud noise then went out on one speaker then later the other


Hello
Your Amps' output section has shorted. Don't connect any other speaker to it, till it has been repaired. It will burn out it too. In some sets this section will be of transistors, and in others, an IC will be used. Anyway it has shorted and has to be replaced. OK.

Apr 19, 2011 | JVC Speakers & Subwoofers

1 Answer

Need jvc rx518v wiring diagram so I can get surround to work right


The JVC site doesn't list that model

http://books.jvc.com/booklist.asp?Model=rx-5

but I imagine it can be a whole lot different frrom the RX-554V

Jan 22, 2011 | JVC Speakers & Subwoofers

1 Answer

Hi i have a older jvc stereo and i have klh audio system model 9706 satellite and i do not know how to do the wiring i can get three spks workig but thats it can u help me do the wireing my jvc has 4 spk...


You can use 4 speakers. Connect 2 speakers to the A system of the JVC and the other 2 to the B system. Then select in JVC the A+B speakers position. As your receiver is stereo, this is the way you could best distribute the sound. However, if you have only 3 speakers, it would be dangerous to try wiring the third one without changing the whole impedance. So you may use 2 speakers.

Sep 08, 2010 | KLH HTA-9706 System

1 Answer

No sound from JVC do have sound from TV connected


hey man my names josh i used to work in home theatre if you can clarify what your problem is i can walk you through it my cell is 832 248 4144 on thing thing yo want to check with that no sound being produced out of of hdmi is to make sure that the port that you have it running to on your tv does not have a set of analog jacks next to it. if thats the case you want get your sound cause you will have to run sound with your hdmi next to that port on the tv that is if your tv has that function and providing you have more than one hdmi port on your tv it will most be the first port you have it pluged into if not you may need to check your wiring and your pre sets on the tv as well as your wiring that your have going to every thing cause i cant promise you that everyting may be hook up like it should but i can straiten that up for ya like i said my name is josh and my cell is 832 248 4144

Nov 02, 2009 | Speakers & Subwoofers

1 Answer

Raised volume cuts sound and gives me "overload" message


A couple of possibilities: Bad solder on power regulators (attached to main heat sink) or cooling fan may not be turning on when volume is raised.

Jan 16, 2009 | Speakers & Subwoofers

1 Answer

Hooking up a klh PSW8-100 sub wofer


Hey you might find a solution on this audio and wiring blog: www.audioholicblog.com -- it has a blog about wiring your home audio system and the cables that you will need.

Hopefully this helps! Good Luck!


Dannyboy!

Sep 20, 2008 | Speakers & Subwoofers

1 Answer

JVC Subwoofer problem.


You may have a break in the wire. You can find out by slowing moving your fingers down the wire until you notice sound coming from the subwoofer. You can fix it yourself by cutting about an inch away from the break both ways. Then cuttings some of the wire off, so the copperwire is exposed. then wrap the two copperwire ends together and seal it with elections tape. or Try replacing the 60 watt subwoofer wire.

Apr 16, 2008 | JVC SP-PW100 Subwoofer

1 Answer

Connecting Bose 901 Series VI Direct Reflecting Speakers to JVC RX-8020VBK Receiver


in order to make those speakers sound good (if they can sound good at all) you need to use equalizer box witch came with them. If your receiver does not have tape monitor loop or preamp to amp jumpers you can not use those speakers. To be honest you do not loose much... none of this stuff is any good (sorry for bad news), but if you like those speakers (I know they have big fans, even if in HI-FI world, they not consider as good) you have to change you receiver. Dariusz


Feb 13, 2008 | Bose 901 VI Main / Stereo Speaker

2 Answers

Reciever Problem


hi, its definetly an internal problem, commonly in the output section, usually its a capacitor or an transistor which is leaky or short. which causes the overload, so u will need a techinical hand to get it resolved.

Feb 12, 2008 | Speakers & Subwoofers

1 Answer

JVC Surround Sound System


The problem on your sub is your speaker is faulty the end of the speaker coil is burnt so at a certain volume it`s makes a short .I hope that would solve your problem:)

Dec 29, 2007 | JVC SP-PW100 Subwoofer

Not finding what you are looking for?
Speakers & Subwoofers Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Speakers & Subwoofers Experts

 Grubhead
Grubhead

Level 3 Expert

4576 Answers

Michael Edwards
Michael Edwards

Level 1 Expert

53 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...