Question about Printers & Copiers

1 Answer

Xerox phaser 8500 09,037.45:12298

Error code

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What kind of error?

Posted on Feb 07, 2008

  • Xcopyman Feb 07, 2008

    well, first check enery, if it turn it on.
    check paper jam, sensors clean it.
    fusor area if it get heat.

×

1 Suggested Answer

pineworks
  • 4041 Answers

SOURCE: Xerox Phaser 8560 - error code 09 037 45 108564

Hi there

That's a ink loader error, due to the 8200 ink stick; to fix it:

- Power down the printer.
- Hold the back button and the info button at the same time, without letting go, power up the printer.
- Keep holding down the buttons until the XEROX logo comes fully to the center of the screen, keep holding for 2 more seconds, then let go. I'll take about a minute or two for the Diagnostic screen to come up, the display will turn blank and black.
- When the Diagnostic screen comes up go to down to the Function or Exercise option, there will be an option that says "clear ISC faults" it'll ask you to press OK to confirm, after you do then you will exit Diagnostics and the printer will reboot.
It should be fine until it happens again. Until all the 8200 ink is gone you will probably be doing this a few more times. Also make sure the 8200 ink is not jammed inside the ink loader, if it is then you have to un-jam it some how.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Xerox Phaser 8560DN error code 07,010,43


Sadly, Xerox says that this means "Power off the printer and contact support". Phaser 8560 Support Drivers

However, there is something about "opening the pivot plate", it's Greek to me, but google it and see if you can't reset the brain in the printer and get it back to life without an expensive service call.

Aug 23, 2014 | Xerox Phaser 8560DN Laser Printer

Tip

XEROX PHASER 7750 7760 FAN ERROR.


Hey guys this is a Xerox Phaser 7750 and 7760 fan error video tutorial.
In this video you will learn how to fix the error code 48 on the Xerox phaser 7750.
Also you will learn how to fix the error codes 010-391,010-392,010-398 that are related to the Xerox Phaser 7760.
This video shows how to remove covers.
All the wires that you need to disconnect from the machine to fix these errors.
There is also another video part two that shows you how to reinstall everything back
in it’s place. Step by step tutorial hope you enjoy.

http://www.youtube.com/watch?v=yMud-Md2xpc


on Dec 30, 2009 | Printers & Copiers

1 Answer

Xerox Phaser error code: 09,038.46:37640


The ink loader 133K27771 is probably defective

Whit
Item, Inc.

Jul 26, 2010 | Xerox Phaser 8560DN Laser Printer

2 Answers

Xerox phaser error code is : 07.002.44:10318 what dose this mean


07,002.44:
PM_FAULT_PROCESS_MOTOR_STALL

Verify process motor operation with the Process Motor diagnostic
test. Also exercise processes run with the process motor;
transfix, drum maintenance and head tilt. This can be caused by
the power control board. The process motor may have more than
one task initiated. Reset all solenoids and the pressure roller
prior to cycling power.

Jun 17, 2009 | Xerox Phaser 8200 Laser Printer

1 Answer

Xerox Phaser 8200 Error Code 15004.45:18370


unless you know how to service preheater/drum heater then you have no choice but to ask the qualified person to do it for you....

YOu can read more details baout the failure at below link..
http://etech.maiila.com/xerox-phaser-8200-drivers-software-manual-and-troubleshooting

Apr 22, 2009 | Xerox Phaser 8200 Laser Printer

2 Answers

Phaser 8560 error code


Most likely you are using generic ink or ink not made for that specific machine. The black ink is the one causing the problem. the printer will then need to be reset.

Apr 15, 2009 | Xerox Phaser 8500/DN Printer

1 Answer

Xerox phaser 8400 error


That is a print head tilt error. Either the print head pivot block is contaminated with ink or the wiper blade is tacked to the print head.
Let me know if you want to try to resolve it yourself, I will send you directions.

Feb 17, 2009 | Xerox Phaser 8550DX Laser Printer

2 Answers

Phaser 7300 Error Code/Message


Seems to be something to do with the Ram.

More help HERE

Jun 01, 2008 | Xerox Phaser 7300DN Laser Printer

2 Answers

Phaser 860 error code 07.003.45:116163


It is a print head tilt error.
Most likely ink is in the stainless steel pivot block at the bottom of the print head.
Also the printer could have been unplugged and the cleaning blade is stuck to the print head.
Or a cable is binding the print head movement.

Nov 12, 2007 | Tektronix Phaser 860DP Thermal Printer

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96333 Answers

old marine
old marine

Level 3 Expert

1453 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...