Question about Samsung WE356A5W Washer/Dryer Laundry Pedestal

1 Answer

SAMSUNG WA2002 Washer

My washer stop working half way, all LED on control panel appears on, after that it not responding when i press any button on the control panel. But after few days, it might work properly again. Help.

Posted by on

  • 1 more comment 
  • amndsk Feb 15, 2008

    same problem... Is it controller problem?

  • wern_st Aug 26, 2008

    I'm having the same problem as I turned on my washer and all LED is on and the machine did not respond to any buttons pressed. please assist in informing on this issue

  • ericr8789 Oct 07, 2008

    i have the same problem on my samsung WA7587 6.0 KG WASHING MACHINE.

    ALL LED ARE LIT AND WOULD NOT RESPOND ..
    AFTER A FEW DAYS IT MIGHT START WELL... AND THEN AFTER A WHILE IT WILL STOP AND SHOW THE SAME PROBLEM.. HELP!!! ARE THIS INHERENT IN SAMSUNG BRANDS..??


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had this problem when I used TIDE 2X detergent (thinking 2X was the same as HE). This happened several loads. I had bought several jugs of Tide (larger ones won't fit in drawer). Somehow grabbed HE one next time and didn't have this problem. Tried the 2X another time or two with again the washer stopping and LED lights on/unresponsive.

Solution was to not use anything but HE detergent.

Still having problem with Fabric Softener dispenser.

Posted on Oct 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front loader washing machine suddenly stop working at there is an LE sign


LG, the electronics and appliances conglomerate, manufactures a variety of high-efficiency washing machines. Whether you have a front- or top-loading model, your LG washer is equipped with an error-monitoring system. When the LE code appears in your display, it indicates a problem with the motor. The problem can be related to several different issues. In order to clear the error, determine which issue is at hand.
New Installation The LE error code may appear in an LG washer's display if installation issues exist. It indicates a miscommunication between the wash motor and the control panel. In most cases, you can simply reset the washer to solve the problem. Unplug your washer before pressing and holding the Start/Pause button for approximately five seconds. Plug it back in and set the washer to a rinse-spin cycle to see if the code has cleared. If the code reappears in the display, contact LG at the phone number in your owner's manual for assistance.
Thermal Overload Protection Your washer may display the LE code if the thermal overload protection circuit in the motor has been tripped. The feature is designed to prevent the motor from overheating and causing permanent damage to the washer. To clear the error code, the motor must cool down. Allow the washer to sit for approximately half an hour before restarting the cycle. If the code reappears, the motor may have an issue that requires a service call. Unplug your washer and contact LG.
Excessive Suds If your washer detects excessive soap suds in the drum, the LE error code can appear. Typically, excessive sudsing occurs when you use too much high-efficiency detergent or a detergent that's not specifically high-efficiency detergent. Always follow the guidelines in your owner's manual and on the detergent label to determine what type of detergent, and how much, to use. To get rid of soap suds in the drum and clear the code, unplug your washer and let it sit for a half hour so the suds can dissolve. Plug the washing machine back in and turn it on, hitting the Spin Speed button and selecting "No Spin." Press the Start/Pause button to turn on a drain only cycle. When the cycle is completed, remove the load from the tub. Start a rinse-spin cycle to clear away any residue. You may need to repeat the cycle to remove all of the suds.
Load Issues The LE error code can appear in an LG washer's display due to certain load conditions. If you are washing a large load, don't choose a gentle cycle like Delicates, Hand Wash, Perm Press or Wool/Silk. Reserve them for smaller loads. To reset the washer, unplug it and press the Start/Pause button for five seconds before plugging it back in. The LE code can indicate that the washer has been overloaded; large loads and bulky items can strain the motor. Remove a few items from the washer to reduce the load size and restart the cycle. If the code appears again, let the washer sit for a half-hour so the motor has time to cool down before you restart the cycle.

Feb 28, 2015 | Washing Machines

1 Answer

The dryer just stopped and now wont turn on


WAKE THE WASHER BY PRESSING ANY BUTTON.

WAIT 5 SECONDS.

PRESS AND HOLD THE START AND PAUSE/CANCEL BUTTONS SIMULTANEOUSLY.

ALL LED'S WILL GO BLANK AND AFTER A FEW SECONDS THE CONTROL WILL SIGNAL THE STORED CODE USING AUDIBLE BEEPS AND BLINKING LED'S. THE CONTROL WILL REPEATEDLY SIGNAL THE CODE, AS LONG AS THE START AND PAUSE/CANCEL BUTTONS ARE PRESSED. A TWO-SECOND PAUSE BETWEEN REPEATS AFFORDS YOU THE ABILITY TO MAKE ACCURATE COUNTS TO IDENTIFY THE CORRECT ERROR CODES.


PLEASE NOTE THE FOLLOWING: ON A SMALL NUMBER OF WASHERS WITH SERIAL

NUMBER PREFIX XC4, IF THE PREVIOUS PROCEDURE DOES NOT PREFORM AS

SPECIFIED, FOLLOW THE OPTION BELOW:

* FOLLOW ALL PREVIOUS STEPS BUT INSTEAD OF PRESSING START AND PAUSE/CANCEL BUTTONS, PRESS AND HOLD OPTIONS AND PAUSE/CANCEL BUTTONS."


*THE CONTROL WILL PAUSE FOR 2 SECONDS, THEN REPEAT THE CODE AS LONG AS THE TWO BUTTONS ARE PRESSED AND HELD."


NOTE: A LETTER APPEARING IN THE CODE STANDS FOR A NUMBER HIGHER THAN NINE: A=10 B=11 C=12 D=13 E=14 F=15 "


"EXAMPLE CODE F1: THE FIRST DIGIT WOULD BE 15 AND THE SECOND WOULD BE 1. IF THIS CODE WOULD APPEAR ON A WASHER IN THE GOOD MODEL LINE, THE FIVE INDICATOR LIGHTS WOULD BLINK FIFTEEN TIMES AND THE START INDICATOR LIGHT WOULD

Jul 28, 2012 | Frigidaire GLET1031FS Top Load Stacked...

1 Answer

F 22 just appeared on my washer. I tried restarting it and it made a clunking noise every 5 seconds and then f 22 appeared again. What does f 22 code for? Thanks,


F-22 is: CCU /touchpad/LED assembly unable to transmit/receive
data to/from the CCU central control unit
Possible causes/procedure:
1. Check the touch-pad/LED assembly by selecting different
cycles and changing the modifiers and options available to
confirm the touch-pad/LED is responding.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the
touch-pad/LED assembly and Central Control Unit (CCU).
themobilian_1012.jpg
Your model's tech sheet gives error codes and remedys.

Duet HE manual and more HERE

Jan 22, 2011 | Kenmore Elite HE5t Washer

1 Answer

Washer stops by itself, have to press start continuously


I would check the inverter on top of the motor. The flashin led light is a code the code legend is on the wiring schematics behind the control panel

May 07, 2010 | GE WBSE3120B Top Load Washer

1 Answer

The Hold to start button is not starting the washer anymore. It used to work but it no longer makes the click that used to start the washer. It seems to be stuck


The user interface board is not serviceable and it requires to be replaced when it is not working properly or when a button is stuck. The procedure is quiet easy and you can do it yourself.

Disconnect power to the washer prior to servicing to avoid electric shock.

Remove the three screws attaching the rear of the top panel to the back of the washer then slide the panel rearward, and then lift it off the washer.

Disconnect the 7-terminal user interface ribbon connector from the left side of the central control unit.

Pull the dispenser drawer out until it stops; press down the release tab then pull the drawer completely out of the washer.

Remove the screw in the recessed hole at the left of the drawer opening. Press and release the tab securing the right side of the console to the cabinet.

Open the washer door then insert the blade of a flat-bladed screwdriver into the slot at the bottom center of the console then push the console up to release the tab attaching its bottom to the cabinet.

Gently pry up and release the top of the console then pull it off the washer.

Pull the cycle selector knob off the control panel then release the tabs securing the user interface/LED assembly to the control panel. Lift the user interface/LED assembly from the control panel once all of the tabs are released.

Inspect the Hold to Start button and the alleged stuck membrane in the user interface board. Replace the button if it is broken. Try your luck by trying to unstuck the stuck membrane. If no luck at all, replace the user interface assembly.

Install the new user interface/LED assembly into the control panel by inserting it into the tabs from one side to the other until it is completely secured, and then reinsert the cycle selector knob.

Align the console tabs with the slots in the cabinet then insert the tabs into position. Secure the left side of the console with the screw previously removed, and then slide the dispenser drawer back in place.

Reconnect the user interface ribbon connector to the central control unit then slide the top panel back into position and secure it with the three securing screws.

Note: The user interface assembly part number may differ from version to version of the same model. The version is indicated by the last digit of the model number so make sure to indicate the complete model number of your washer located on the left side of the door opening.

Mar 15, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Control locked light is on and washer won't turn on. Can press "Control On" and Cancel/Pause buttons at the same time to get the power on but won't start.


Looking at the manual of my Whirlpool front loader gives me the following advice...

CONTROL WON’T ACCEPT SELECTIONS
1. Press PAUSE/CANCEL button on the touch-pad twice.
2. Drain the unit, then check that the drain hose and drain
pump filter are clear of foreign objects.
3. Check the touch-pad/LED assembly by selecting different
cycles and changing the modifiers and options available to
confirm the touch-pad/LED is responding.
4. Unplug washer or disconnect power.
5. Check harness connections.
6. Plug in washer or reconnect power.
7. Verify CCU operation by running a Diagnostic test or any
cycle
BTW: The full manual is at http://www.servicematters.com/docs/wiring/Tech%20Sheet%20-%208182208.pdf

Mar 07, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore elite calypso doesn't respond to buttons except cancel


I've had a similiar problem on my calypso. In my case the key pad would go dead after washing or pushing stop after a few minutes. If I unpluged the unit for a few minutes it would work again. This would appear to be in the controller board. I removed the board and inspected it finding no problems. After re-installing the board the washer appears to be working again. My conclusion is that there is a loose connector/connection. I'd suggest you remove and re-install all the connectors on the controller board. This is the board closest to the power chord.

Good Luck, George S.

Sep 10, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

2 Answers

Samsung washing machine F1245 control panel stuck??


I have Samsung/korea-SW905Washer.When power is switched on the Fault-'1E' appears. what could be the reason.( narrate list of control component failure).
Bought in the year 1996 at India ( voltas mega washer top loading-7.5kg) and working till last month.
after few wash cycles the machine stopped at aforesaid indication and it is not functioning due to above fault indication'1E'
provide me remedial measures or electronic control board circuit.

May 29, 2009 | Samsung WE356A5W Washer/Dryer Laundry...

1 Answer

Whirlpool duet washer has stopped and the LED indicator says sud


The filter on your pump is probably clogged with lint and stuff. You have to remove the bottom front panel, 3 torx screws underneath. The panel will drop and come off. Drain off the excess water from the drain pipe you see. The white filter cover is right in front. Get yourself a good plastic bag to collect water. Unscrew the filter cover and twist the filter out. Clean out all the stuff and put it back in carefully. Check your pump too, comes after the filter.

Apr 09, 2009 | Whirlpool GHW9200L Front Load Washer

Not finding what you are looking for?
Samsung WE356A5W Washer/Dryer Laundry Pedestal Logo

557 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Chris Haynie

Level 1 Expert

3 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...