I can't keep it running. It will runn on high rpm for about 30 seconds then it bogs down and stalls and I cant keep it running at idle without the choke half way on

no VIN 8th digit told.(engine)
well; if a tune up fails (spark plugs) and Spark COP boots.
then check fuel pressure by the book.
bogs under load,
stalls means engine stop spinning as in zero RPM./
loss of power or bogging , and not violent loss, means mostly fuel supply is weak. or low injector rail pressure found
a shop has the tool to do that, why not put them in the loop>?

see the diagram attached and proceed and fix it. God bless you

For this types of problem,there are few help inks to troubleshoot the problem.Click the link below to go through the troubleshooting procedure to resolve the issues :----Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html-----------van idles rough? http://howtobyme.blogspot.in/2012/01/2004-ford-freestar-van-idles-rough.html
--------------runs lean and idles rough? http://technoanswers.blogspot.in/2012/02/ford-runs-lean-and-idles-rough.html
-----------Car still runs Rough after tune up? http://howtobyme.blogspot.com/2011/12/car-still-runs-rough-after-tune-up.html
------------Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed? http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html
----------High rpm in neutral? Inconsistant high RPM in neutral? http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html
------------Engine Backfires? http://technoanswers.blogspot.in/2012/02/jeep-backfires.html----------- Nissan stalls and bucks on Acceleration?

http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-stalls-and-bucks-on.html

-----------
Nissan Pathfinder Backfires? http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-backfires.html
---------How to adjust rpm? http://schematicsdiagram.blogspot.com/2011/12/how-to-adjust-rpm-on-2009-dodge-charger.html
------------Engine cuts out at 3000 RPM? http://schematicsdiagram.blogspot.com/2011/12/engine-cuts-out-at-3000-rpm.html
----------This will help.Thanks.

Your only problem friend, is the temperature sending unit/sensor. Upon cold start, this sensor wil tell the computer to go into cold start mode putting a bit more fuel in and raising the idle a bit to keep it running when cold without using the throttle. Replace that sensor and your good to go. Makes sense, right?

check the air flow meter operation and rangeing

I had a similar problem and the mechanic diagnosed it as a problem with the ignition coil. So you might want to get that checked.

The main jet need cleaning.(you should clean them all though)

Main Jet: Main jet comes into play at three-quarters open to full throttle conditions. CRITICAL to high-speed engine operation. Not only does it meter the gas into the engine, it can aid in cooling the engine as well.

Please rate this Fixya

The H is for when your cutting,it keeps the saw from stalling. The L, is for the saw when at Idle. When the L ,is adjusted right, the saw should stay running ,and the chain should not move ,that is with the break in the off position. The H screw,should be adjusted if the saw bogs down when rev ed up. A good starting point for theses screws would be a turn and one half out.

YOU MAY HAVE A IDLE SPEED CONTROL VALVE PROBLEM, CLEAN IT FIRST, THEN DISCONNECT THE BATTERY, FOLLOW THE PROCEDURE I HAVE ATTACHED.

Here is the most common cause of this stall and idle speed issues, it is the idle speed control air-bypass valve and throttle valve, they get full of gunk over the miles and cause idle issues (stalls) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.