Question about Car Audio & Video

1 Answer

How to remove starter chevrolet 1994 k1500 5.7 liter 350 cubic inch z71

Where are the bolts on the starter

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,039 Answers

You might have a flash pan on the trasmission 2 bolt in the bottom 2 on top remove the trasmission flash pan go easy you have the trasmission cooling line there if there rusty they might leak if you move them to mush you should see the starter 2 long bolt the 2 bolt go right trus the starter but the number 1 thing disconnect the battery first thank you for using fitya pierre

Posted on Feb 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What arm the specs for 95 camaro lt1 350


Block and Basics
Displacement: 350 cubic inches, 5733 cubic centimeters, 5.7 liters
Block Material: Cast Iron
Main Bearings: 2-Bolt Centers and Ends (The Corvette LT1/LT4 had 4-bolt mains)
Stroke: 3.48"
Bore: 4.00"
Compression Ratio: 10.4:1
Combustion Chambers: 54 cubic centimeters
Factory Redline Rating: 5700 Rotations Per Minute

Bottom End
Piston Material: (10159437) Eutectic Aluminum/Silicon Alloy
Connecting Rod Material: (10108688) Powdered Metal
Crankshaft Material: (12556307) Cast Iron

Top End and Valvetrain
Cylinder Heads: (10168448) Cast Aluminum, 2 valves per cylinder/16 valves total, ~212 CFM flow (Impala SS and Caprice heads were made of cast iron*)
Valve Diameter: (intake- 10241743, exhaust- 12550909) 1.94 intake, 1.50 exhaust
Valve Overlap: 41*
Valvesprings: (10206040) 85 lbs, seated
Camshaft Specs (12551705): 205/207 duration @ 50*, .447/.459" lift, 117 Lobe Seperation Angle
Rocker Arms: (10089648) 1.5:1 Stamped Steel
Timing Chain: (10128485) Powdered metal link

Intake and Fuel Delivery
Fuel Delivery: Electronic Fuel Injection, sequential port
Injector Size: (17124248) 3.0gps, 22lbs/hr speed density (1992-1993), 24lbs/hr mass airflow (1994-1997)
Throttle Body: 48 millimeter twin butterfly
Intake Manifold: (12552137) Aluminum

Factory Power Ratings
92-96 LT1 Corvette: 300bhp, 330lb-ft
1996 LT4 Corvette: 330bhp, 340lb-ft
1992 LT5 Corvette: 375bhp, 370lb-ft
93-95 LT5 Corvette: 405bhp, 385lb-ft
93-95 LT1 F-Body: 275bhp, 325lb-ft
96-97 LT1 F-Body: 285bhp, 325lb-ft
96-97 WS6/SS: 305bhp, 335lb-ft
93-97 Firehawks: 315bhp, 340lb-ft

Factory LTX Camshaft Specifications**:
1992 Y-body: 205/207 0.451/0.450 lift 117 LSA
1993-1995 Y-body, F-body: 202/207 0.450/0.460 lift 116 LSA
1994-1996 B-bodies (including L99 4.3L): 191/196 0.418/0.430 lift 111 LSA
1996 Y-body, 1996-1997 F-body: 200/207 0.447/0.459 lift 117 LSA
1996 Y-body, F-body LT4: 203/210 0.476/0.479 lift 115 LSA


hope this helps

Mar 04, 2015 | Cars & Trucks

1 Answer

Removal of starter off a e350 cargo van 7.3 liter diesel year 2000


DISCONECT BATTERY STARTING WITH NEGATIVE
REMOVED WIRES AT STARTER
REMOVED BOLTS HOLDING STARTER TO ENGINE
REPLACE IN REVERSAL

Jul 08, 2011 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

How to change the starter from my 1994 chevy camaro


REMOVAL & INSTALLATION 3.4L and 1993-95 5.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If necessary for access to the starter, disconnect the exhaust crossover pipe from the manifolds.
  4. Unfasten the two starter mounting bolts/screws and carefully lower the starter motor.


To install:

Before attaching the electrical connectors, tighten the inner nuts on the solenoid terminals. If the nuts are not tight, the solenoid cap could be damaged during installation of the leads. Tighten the inner nut of the "BAT" terminal to 80 inch lbs. (9 Nm).
  1. Fasten the electrical leads to the starter motor assembly. Tighten the solenoid switch "BAT" terminal outer nut to 80 inch lbs. (9 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
  2. Position the starter motor to the engine and install the retaining bolts/screws. Tighten to 35 ft. lbs. (47 Nm).
  3. Measure the starter pinion-to-flywheel clearance and add shims, if necessary.
  4. If removed, connect the exhaust crossover pipe to the manifolds.
  5. Carefully lower the vehicle, then connect the negative battery cable. Tighten the cable to 11 ft. lbs. (15 Nm).

Hope helps.

Sep 06, 2010 | 1994 Chevrolet Camaro

2 Answers

How do you replace the starter on a 1989 SW1500?


The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
  1. Disconnect the negative battery cable at the battery.
  2. Raise and support the vehicle.
  3. Disconnect and tag all wires at the solenoid terminal.
Reinstall all nuts as soon as they are removed, since the thread sizes are different.
  1. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.

f6823f2.gif
Starter mounts-5.7L and 7.4L engines

  1. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck.
To install:
  1. Position the starter and tighten all bolts as follows:
R/V Series:
  • Thru-bolts: 40 ft. lbs. (54 Nm)
  • Bracket bolt: 30 ft. lbs. (41 Nm)
  • Nut (gas): 11 ft. lbs. (15 Nm)
  • Nut (diesel): 90 inch lbs. (10 Nm)
C/K Series:
  • Thru-bolts: 35 ft. lbs. (45 Nm)
  • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
  • Nut (diesel): 75 inch lbs. (8.5 Nm)
  1. Reconnect all wires.450af3b.gif

Disconnect the negative battery cable


56132e9.gif
Remove the starter retaining bolts


d54e957.gif
Remove the starter from the vehicle

Apr 26, 2010 | 1989 Chevrolet Suburban

1 Answer

I NEED YEAR & SIZE FOR A CHEVY ENGINE. ID #V1016UKA


it was built in flint michigan on october 16th 1981, and intalled into a c-30 van or c-3500 truck with a 159.5 inch wheelbase. originally had a 2 barrel carb. had about 150 horsepower. 350 cubic inch 5.7 liter. originally had manual transmission.vin code on original vehicle was P LF5.

Apr 05, 2010 | 1988 Chevrolet C1500

2 Answers

What size motor does my stock 1990 CHEVROLET K2500 have


it can be either eng, you tell by the VIN of the truck or the federal emission sticker above the radiator

Sep 08, 2009 | 1990 Chevrolet K2500

1 Answer

What engines were available in 1996 monte carlos


3.1 liter 189 cubic inch V-6 or a 3.4 liter 207 cubic inch dual over head camV-6

Jul 03, 2009 | 2000 Chevrolet Monte Carlo

1 Answer

Cubic inch


If it is Single camshaft it is 3.1 liter or 190 cubic inches.If it is double overhead cam it is 3.4 liter or 207 cubic inches. Hope this helps.

Dec 20, 2008 | 1995 Pontiac Grand Prix

1 Answer

How do I change the starter in 1994 Silverado 350?


Man, your in luck, the '94 starter is fairly easy to change. Two bolts are that holds it on. Just disconnet the solenoid wires, take out bolts. Reverse for installation.

anaanymous

Oct 07, 2008 | 1994 Chevrolet K1500

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4789 Answers

yadayada
yadayada

Level 3 Expert

69014 Answers

The Knight
The Knight

Level 3 Expert

72214 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...