Question about Car Amplifiers

1 Answer

Car amp I can not find a dealer that has a power plug for the man power in. What can i do ?

Posted by on

  • Paul Teichmann May 11, 2010

    You'll need to post the amp's brand and model #.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 218 Answers

Maybe a picture of the receptical would help too.

Posted on Feb 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where can I find the power plug for this amp?


are you sure there is a power plug needed for the amp? very few amps require power plugs. you merely have to run wires to the power terminal. the power terminal should be labeled - pwr (b+), grnd, and rem.

Dec 01, 2010 | Lightning Audio Strike S2.600.2 Car Audio...

1 Answer

JL Amp isn't powering subs and speakers


just go through ur connections man one by one ull find the prob soon.....check teminals on battery...power line to amp ....all fuses within prob area and obviously make sure u have a good ground.....really impotant.....ground is the most neglected thing people do from my experience bein a audio tech oh and if that isnt it check ur subs....stick a 9v batt on the back pos n neg of each sub n c if they pop in r out this will determine if ur subz r blown

May 14, 2010 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

Power blue light is working but there is no sound?


check ur rcas man n then fuses on amp check rca connections on back of ur deck

May 14, 2010 | Rockford Fosgate T30001 bd Car Audio...

1 Answer

I have a twelve hundred watt sony explod amp and a couple twelve inch subs i killed a deer awhile back and put it in the back of my suv every since then my amp will power on light up everything it should...


Does the amp power up? Did you knock the fuse loose with a deer hoof? Sorry couldn't resist that. Check all of your wiring with an ohm meter especially your speaker cables. Check for DV voltage at the power input to the amp and also the remote turn on. If you get voltage there try turning the amp on and measuring the AC output voltage of your amp from plus to minus. (crank the volume up) That will also tell you if your amp is functioning. Verify signal to the amp. If you have a portable stereo with aux inputs drag it out to your car and plug your RCA into it. If you get sound to your portable stereo you have signal. You can't reliably measure the AC voltage with a meter because it is so low, if you had a scope that would work. Test your subs on your home stereo, (verify impedance first). These are just some ways to divide and conquer good luck man!

Dec 21, 2009 | Sony XM-2150GSX Car Audio Amplifier

1 Answer

What is the maximum size gauge wire I can use to power my mc427?


well in general for most amps man i would run no thiner than about a 4gauge wire for the power and ground and for your remote contection on the amp you will need about a 12-14 gauge wire

Oct 31, 2009 | Car Amplifiers

1 Answer

My sound cuts out and the power light blinks consistantly about 3 times and now i have no bass and the power light comes on about every 20 seconds and then shuts off


the amp it going into protect mode because there is an internal fault with the amp. it will need to be repaired. best this to do is find a repair shop and let them handle it good luck man

Oct 24, 2009 | Jl Audio Slash v2 500/1v2 Car Audio...

1 Answer

Jl audio 500x1 not working


Im not sure if you a very knowledgeable of car audio but first make sure the rca's are plugged in!!!! Then make sure the gain is all the way up on your amp, well atleast some of the way!!!!! Maybe they were real dirty and decided to cut your rca's somewhere in the car so they llok like there still hooked up but maybe they really aint!!!!! maybe your amp is fried!!!! But remember it worked fine when you brought it to them!!!! They are trying to stick ya man!!!!

Feb 24, 2009 | Jl Audio Car Amplifiers

1 Answer

Power and protect light blink red


disconect speaker wires from and amp and repower if light is still on disconnect RCA jacks and repower if protection is still on you have a solder jump inside your amp send it in for erepair to dealer or buy a new amp at dealer prices at www.godspeedaudioheaven.com

Feb 03, 2009 | Alpine MRV-1507 Car Audio Amplifier

2 Answers

800.2


Well when you blow a sub it can definantely short your output fets in the amp.

Nov 09, 2008 | Rockford Fosgate 800.2 Car Audio Amplifier

1 Answer

Amp kills battery


in first are you sure that the connectics are correct?? to plug your amplifier to your electric system on your car you have to plug the positive (Big Red) to the positive battery via a fuse breaker, the ground(Black) must be connect to the car frame and it has to be shortly, and the last connection blue must be connect to your switched ouptput on your radio.
If this are correct you have to use an amperemeter to follow your leak, for this you have to go to a electrical car specialist. ;)

Mar 31, 2008 | Sony XM-2200GTX Car Audio Amplifier

Not finding what you are looking for?
Car Amplifiers Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...