Question about RCA TruFlat 27F520T 27" TV

1 Answer

Channel i cant get any channel on my tv it say tv3 mono what can do to get a channel

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Make sure that ur antenna/catv is properly connected to antenna/catv input of ur tv...better check the center lead if ur using coaxial cable..then try to reprogram/autoprogram ur set.
navigate also on tuner settings...via remote..
if u get nothin after autoprogram..probably bad tuner in ur set..u need a prof tech to fix it...thanks hope this help

Posted on Feb 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tune samsung tv


Mono is the first point I am stuck on. Mono is an audio reference but I am going to assume that you are only receiving the analog channels and not the digital. If you are coming off of an antenna then the antenna has to be HD to receive HD channels over the air. If you are off of a cable box then this has to be dealt with from your provider. You will also need an HD ready TV or if you do not you will need an HD converter box to make your tv work with the digital signal.

Apr 02, 2014 | Televison & Video

1 Answer

Picture problems on tv3


you have to turn off the PIP option in the settings either in the remote controller or in the menu settings using menu button at the tv to go in the set up.

Dec 28, 2012 | Televison & Video

1 Answer

What does a mono status mean on the tv screen?


It does not mean much---sound may still be stereo but channel change often does not allow it to show.

With it on a channel listen carefully and switch it if possible from mono to stereo to see if hear mono or not.

Jun 11, 2012 | GPX Televison & Video

1 Answer

How do I retune My toshiba ct 90240 hd tv


Just download the user manual to your tV from internet. It will have all the details. Get into 'toshiba.com/download/manual' site.

Apr 09, 2012 | Televison & Video

1 Answer

How do I get my rca truflat tv to get out of mono?


Hello
Press the MTS on the remote control handset to select STEREO, MONO or SAP. All the options will be available only when the current TV channel is broadcasting that option. Channels will not always carry programes, that have all MTS options. If "STEREO" appears on the screen when you select a channel means stereo sound is available with current programme. You can hear sound from both speakers. If broadcast is not strong and clear, stereo sound will not be available. Press "MTS" button to change it to "Mono". This will eliminate the noise. If "MONO" appears on the screen when you select a channel, stereo effect will not be availabe, even though you have set it to stereo. If "SAP" appears when you select a channel 'Second Audio Programe' [SAP] broadcasting is available for that programme. Press the "MTS" button to 'SAP' and you can hear that programe in different language or some other kind of audio.

Oct 28, 2010 | RCA TruFlat 27F520T 27" TV

1 Answer

How can i bridge a mtx 9500 using a mono amp?


You cant bridge it to the MONO AMP . You can only bridge subs & speakers to 2 CH & 4 CH AMPS that are bridgeable. Because if it appears that there is 2 channels on a Mono amp its so its convenient for you to hook up 2 4ohm subs to it easily But both channels are actually connect internally together in parallel inside the amp unlike a 2 channel they are separate.

So just connect your mtx 9500 to a plus and a minus and doesnt matter which since all the + terminals of are connected together and - are connected together already.

Whats important is on the side of the sub/box it reads 2 ohms. The lower the ohms the more power the Mono amp will put out. Mono amps are designed to handle 2ohm loads.

If it reads 4ohms The MONO amp is the wrong amp to use cause the power will be weaker. So if you have a 1000 Watt Mono amp at 4ohms the sub will only get 500 WATTS Max while a 2 ohm will get the full 1000 Watts.

If it reads 4 ohms connect it to a 2CHANNEL AMP and BRIDGE IT (connect + of the sub to 1st channels positive of the amp then connect - of the sub to 2nd channels negative of the amp) . The power will be doubled when you bridge it on a 2 channel amp. NOW if it was a 2 ohm sub and you bridged it to the 2 channel amp it will fry the subs and ruin the amp. 2 CHANNELS CANT TAKE A 2OHM LOAD BRIDGED OK.

Apr 08, 2010 | MTX (SLH-T7512X2-A) Car Speaker

1 Answer

Cant get mono off tv screen ..


The TV set itself will probably have a button that is marked either "Video," "Input" "Source" or "TV/VCR" - I would need to have your exact television model # to be sure. Make sure the cable box is on. Press the Video/Input/Source/TV/VCR etc button and see if your cable picture reappears on one of the source channels. If your television is connected to the cable box with a standard coaxial cable, then Ch.3 or Ch. 4 would be the right choice. If you have a digital cable box, however, the cable is probably going to be on an auxillary channel. If you give me the exact model # of your TV, and the type of wires that run from your cable box to your TV, I can give you more precise instructions. Good luck!

-Tha Mp3 Doctor

Feb 11, 2009 | RCA M4204 MP3 Player

1 Answer

T v channel


Tuners are a big source of problems on this model, i may suggest using your cable or sat box as the tuner by going from the video out of the cable or sat box to the video input on the tv, select video on tv and let the cable box1.gif or the sat box act as the tuner, if you are using outside ant then use a vcr as your tuner to the set. this is a easy and cheep way to fix your problem.
hope this helps ya.

Feb 05, 2008 | RCA TruFlat 27F520T 27" TV

1 Answer

No Sound


Maybe a vacant channel or input is tuned.
• If watching VCR (connected only through antenna input), make sure TV is tuned to channel 3 or 4 – same as CH3/4
switch on VCR. Also check to make sure the TV/VCR button on the VCR is in the correct “mode.”
• Simultaneously press the POWER and CHANNEL DOWN buttons on the front panel to reset the TV.

HOPE THIS WILL HELP YOU.. GOODLUCK

Jan 29, 2008 | RCA P61310 TV

2 Answers

Akai LCT3785TA stereo vs. mono issue


Well the default is to obtain the channels signal. most channels over the world their audio output signal is mono. Rare tvs have the ability to save indivisual channel to their memmoty. Read the tv prospectus!!!

Sep 04, 2007 | Akai LCT3201AD 32 in. LCD Television

Not finding what you are looking for?
RCA TruFlat  27F520T 27" TV Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72620 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...