Question about RCA MM32110 TV

1 Answer

RCA M32110 Hello, Trying to find where I can purchase a new circuit board for a RCA mm32110 It's the board on the top of the tv which has the power on/off Volume up/down and has the IR receiver attached to the board. The part #'s I can find on the board are (xx15568-730) ( rwb55300493) (15472668) The buttons work fine the IR Receiver part does not seem to work . Even with a new remote designed for this tv. I would solder in a new IR Receiver, But I'm not sure of the specs on it. Looks like a Vishay tsop312 series Thanks in advance gpgriffith@aol.com

Posted by on

  • GPGRIFFITH Feb 05, 2008

    Dobbins99506.

    Thank you for your quick response. I'll find one and give it a try!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 113 Answers

The remote Ir receiver for this television is RCA part number 245282. I could not find the whole board available but this was available at many places.

Posted on Feb 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rca f35755mb - when i push the power button on it clicks on then off three times and then stays off. what is going on?


Hello,
You need to check the output voltages of the power supply to see which one goes off. It may be due to short circuits some where,if otherwise power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement. Hoping this will help in solving the problem...

Aug 08, 2011 | RCA F35755MB 35" TV

1 Answer

My tv wont turn on the power button just blinks when pressed on tv


Hello,

Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.


I hope this will help in solving the problem........

Dec 17, 2010 | RCA F32650 32" TV

1 Answer

How do I replace and purchase the power fuse on a RCA model F35760mb


To purchase a fuse you have to visit your local electronics parts center or in home workshops. To replace the fuse, open the back cover of the tv set and locate the end of the cord which is soldered in the circuit board. beside it is the fuse holder replace it. Make sure to unplug the unit while doing the replacement to avoid electrical shocks.

Nov 17, 2010 | RCA F35760MB TV

1 Answer

How do we hook a dvd player up to tv


conect with scart cable and put t.v. on a.v. channel

Jul 31, 2009 | RCA MM32110 TV

1 Answer

Picture blurry, now doesnt turn on. a circuit board sparks under middle lamp.


Your problem tends to be due to bad solder or defective power supply board in your tv .
You need to check the soldering in your tv .

For power supply board you can get from the link below

Power supply board for RCA tv

Hope this helps .

Feb 28, 2009 | RCA HD52W58 52" TV

1 Answer

RCA F32650 Bad Circuit Board


try pts electronics, just go to search engine and type board number and it will tell where yoiu can buy it . at least 250.00
though.

bc

Feb 26, 2009 | RCA F32650 32" TV

2 Answers

MENU COMES UP AND MUTES ITSELF


check to see if your remont control dont have the mute button blocked down

Dec 11, 2008 | RCA MM32110 TV

2 Answers

Circuit board 1547266C


remove the board and clean it with rubbing alcohol while pushing the switches in and out. allow to thoroughly dry and reinstall.
worked for me.

Dec 30, 2007 | RCA F32650 32" TV

2 Answers

Power on and off repetitive


need more info but it sound to be a cold solder problem,look at the circuit board closely for cracked solder joints. Resoldering any bad joints might just solve your problems, but be carefull there are very dangerous site inside a tv, if you dont know about tvs look for profecional assistances..good luck

Aug 06, 2006 | RCA 36V430T 36" TV

1 Answer

Loose Picture (Goes completely Black)


Nothing special about that board as I cant seem to find that # but If my memory serves me correctly it sounds like a crt board and its a simple soldering job on the crt socket?? Altough Im not there to see the set still 550.00 seems like an awfull lot to repair a set even if they have to replace the entire chassis. I think you should cal rca and take it to an authorized RCA repair center and if the shop you took it to was an rca authorized center I would also report that to them(RCA). Good Luck

May 16, 2006 | RCA MM32110 TV

Not finding what you are looking for?
RCA MM32110 TV Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68157 Answers

John mullen

Level 2 Expert

245 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a RCA Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...