At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: Whirlpool washer - basket will not fill with...
Sounds like the outer tub has a hole in it. Some of the newer models had a problem with the inner tub (basket) would rub a hole in the outer tub about 2/3 the way up.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The following images identify an invention that most newer machines included, The ring about half filled with water automatically balances the basket of the washers. If the water has leaked out or the ring has failed the machine will not achieve balance. The ring is replaceable by qualified DIY.
Most units only have the ring on the top of the basket, but some as the bottom image shows have two.
No cannot over ride set at large doe the machine fill to a certain level then stop if so operating correctly if it never stops filling with water then there is a leak in the fill system either a hole in pressure switch hose it popped off tub or water leaking out thru drain system pump or siphoning thru hose again if unit starts to agitate there is enough water in unit per design
You should be able to put it in spin and remove the water. if it don't you have a problem somewhere. There should be 3 springs hooked to the bottom of the tub to hold it on center if one breaks or comes loose it will be off balance. If you get water in the tub when not useing it and the water is on from the water line the water valve is leaking.If the water don't shut off when filling the water level switch could be bad.or the tube running to it could be stopped up pull the hose off the water level switch and blow through it if it bubbles in the tub it is ok. If can't blow through it it is stopped up.Hope this helps
Hi, the water-level switch regulates your washer's fill volume. This switch is usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. If the switch is defective, it may prematurely signal the water to shut off. If so, you probably need to replace the water-level switch.
As the tub fills with water, the water level switch detects the pressure of the air trapped in the tube. When the pressure reaches a certain point, it turns off the water and starts the wash cycle. As long as the tube that connects to the water level switch does not leak any air, it should be fine.
Thanks for using FixYa. Error LF means long fill, which flashes when the water level won’t change for a period of time after the valves are turned on or the water has disengaged the basket but control does not detect a water level change. TO resolve this issue check if the water supply is turned on and the hose screens are not plugged or kinked. If the water is not entering the machine then check the water valve, also check the pressure hose connection to the machine/motor control. Please do rate the solution if the issue is resolved or post a comment for further assistance.
Remove the back cover.
Inspect the basket for any leakages by filling the water in the basket.
If located weld it or seal it with ARALDITE adhesive.
Also check the outlet valve at the base of the basket.ensure that outlet valve is seated properly.
This should be able to fix the problem, if not then you have to call service engineer to heck the functioning of control panel.
Your drain line is too low or has no air gap causing it to siphon water. Raise the drain line. Do not use a rag or duct tape to keep it in the drain hole.
Check the water level switch. This is a diaphragm-like device with a small plastic tube attached between the switch and the bottom of the washer's outer tub. As the water level increases, so does the pressure on the air in the plastic tube and when it reaches a certain level, it activates the switch to turn off the water and signals the timer to start the appropriate cycle. Look for any obstructions in or damage to the plastic tube. The switch can be tested using a multimeter or ohmmeter. Check for continuity. A lack of continuity indicates a bad switch. Sorry for your trouble and I sure hope this helped. Best wishes.
Thinking of 2 things either the transmission is out or the clutch is
burnt out and the drum basket and possibly the drive shaft broken as
well. Prices vary greatly by how many of these things are broken but
should run between 100-200 including labor.
×