Question about Hunter Fan Company 5/1/1 Programmable Thermostat

1 Answer

Termostat problem We have the old model #44402 002. They say low battery. We put new battery, the screen is scremble. Please help us, what I should to do.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

Try removing the battery and leaving it out for a full minute, then put it back it. SOmetimes it's necessary for electronics to 'settle down' and reset when the power is remove and re-applied too quickly.

Hope this helps, and please remember to rate my answer, good OR bad.

Good luck!

Posted on Feb 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put in a new water pump. New thermostat. Put in my coolant but the coolant isn't pumping around n the car is over heating. Can any one help


Try removing the termostat and run without.
if it cools Down you have Wrong termostat.
if not you have a blown headgasget.
br
soren Halling,

Jan 14, 2016 | Cars & Trucks

1 Answer

Undefined


Most likely the old battery was so low the scale was reading low.

Oct 13, 2014 | Health & Beauty

1 Answer

How to change thermostat


The Termostat fit inside the Termostat Housing. It normally links to one of the radiator hoses leading from the engine block or radiator. Depending on the model you have, the termostat housing needs to be opened, the old termostat removed and the new termostat inserted. It's quiet simple. Before closing up, make sure that the both surfaces on the housing are clean and free from dirt and old sealant. If you remove a gasket, then replace with new gasket. If the housing takes a rubber O ring, then it is advisable to replace this.

Good Luck

Dec 29, 2011 | 2004 GMC Yukon

1 Answer

Bord short


Thats a too old model and expecting a good backup isnt fair. tr removing wallpapers or screen savers for a better backupcant help more then thisor else get a new battery . but nokia isnt manufacturing'em u need to get one from local brand

Nov 23, 2011 | Nokia 1100

1 Answer

Hi, ihope you can help with this one. I have a Toyoa celica Carl sainz model. My garage has swapped the engine block, the old one had a crack. But now it is direcly overheating while the radiator stays...


Remove thermostat (temporarily) to verify if coolant passage ways are blocked. If it circulates with thermostat out, then your thermostat needs replacing.

Mar 05, 2011 | 1991 Toyota Celica

1 Answer

Whenever I put new batteries into my Canon Powershot A480, I get the same thing - I get the 'Low Battery' red flashing light. And Then as I go to take a picture it shuts off and says ; Change The Batties....


I've got the same problem with 2 A 480 canon. I put in NiMH batteries and they work fine. If you put in slightly drained used batteries they work!! Nimh batteries are 1.2 volts and Alkaline are 1.5 volts. There is definitly a problem with this camera. I measured the voltages of brand new batteries 1.51 volts each and they didn't work. I put in some old batteries 1.4 and 1.42 volts and they worked fine.

Dec 17, 2010 | Canon PowerShot A480 Digital Camera

1 Answer

The furnace send signal to the fan in about 30 seconds, now this fan is set in auto from my termostat, my problem is the fan is starting slowly and some time it don't start, but if I use the option manual...


Depending on the model of the furnace, the blower is either a 2 or 3 speed. When the furnace operates in heating mode with the thermostat in the auto position, the furnace starts the fan when the furnace reaches a specific temperature or after a set time delay, but it operates the fan in low or med low speed on heat mode, when you put the thermostat fan switch in the "ON" position, the furnace operates the fan in "HI" speed, the same speed used for cooling mode. You may have a blower moter that is starting to short. I would recommend having a professional replace the motor before now before it becomes an emergency in the middle of the night during a cold spell.

Oct 10, 2009 | Heating & Cooling

1 Answer

Installing a new termostat


Depends on the brand of unit you are running.
Brand and model number please.
Most are on "O".
Hook it to "O" and run the unit. if it runs correctly in Heat and Cool, you are OK.
If not switch it to the "B" terminal.

Apr 12, 2009 | Heating & Cooling

1 Answer

Always says low battery; when new battery inserted, it froze


CALL DIGITAL POWER PRO @ 801-934-6269 OR GO ON-LINE TO DIGITALPOWERPRO.COM,
THEY SHOULD BE ABLE TO HELP YOU. I BELIEVE YOUR BATTERY IS COMPATIBLE WITH THE FUJI NP40

Feb 17, 2009 | Vivitar ViviCam 7500I Digital Camera

Not finding what you are looking for?
Hunter Fan Company 5/1/1 Programmable Thermostat Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hunter Dryers Experts

Fan Fair Of Boca
Fan Fair Of Boca

Level 3 Expert

1617 Answers

Paul Bade

Level 3 Expert

1413 Answers

yadayada
yadayada

Level 3 Expert

71856 Answers

Are you a Hunter Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...