Question about Televison & Video

2 Answers

Viore 20" LCD user manual

I am looking for a user manual for a Viore 20" LCD TV. I am trying to connect a Receiver to the TV so the sound comes from the speakers instead of the TV. Any idea where I can find that information?

Posted by on

  • fourbays Feb 06, 2008

    Thank you for the suggestion. I have quite a few connections on the back of the TV including a Component connection which connects the Blue/Green/Red/White/Red series cables. I thought that would work as an Audio Out. Do you know where I can get a manual from for that TV?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Www.viore.com has user manuals listed

Posted on Apr 20, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 113 Answers

The tv has to have an audio out on the back to allow this to function. A lot of your cheaper smaller LCD'S do not have a audio out. If you have a higher end receiver you can connect all you components IE...dvd,cablebox,videogames...and run one connection from you receiver to your tv.

Posted on Feb 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a perfect picture but no sound. What can be the problem?


Toshiba says:
toshiba_icon_white.pngIf there is no sound from the TV try the following:
  • Ensure the TV isn't muted.
  • Check that the TV speakers have not been manually turned off in the menu settings. Refer to the User's Guide for your specific model TV.
  • Ensure the input for the connected device (DVD / Blu-ray / Cable / Satellite / Game Console) is set properly on the TV. Click here for help with TV inputs.
  • Check that the connected device audio settings are configured send sound through the audio input connected to on the TV. Refer to your device manufacturers instructions.
  • Make sure the connected device does not require a separate audio connection to the TV

Jan 28, 2015 | Toshiba 50H82 50" Rear Projection...

1 Answer

I'm trying to reset my viore tv but it want stay on long enough


My Stand By light,Timer/Temp light,Lamp light is blinking. My T.V will come on for just a few minutes then it shuts off. then my lights flash on and off.

Mar 12, 2011 | GRY Viore RPT50V24DHD 50" HDTV DLP TV

1 Answer

I transfered from watching my sattelite tv to watching a dvd using the tv control. The dvd sound worked ok, but I couldn't get a pictue. Then I tried to watch tv again, but the vidio would not come in,...


Just in case, here's the 108-page user's manual for your TV:
http://www.hdtvsolutions.com/pdf/MIT_WD-52525_WD-62525_WD-52725_WD-62725_Manual.pdf

Yor "NetCommand" TV remote is a wondrous thing, capable of throwing off anyone.

When the 'Device Selection Menu" is dispayed, and only when the device icon is highlighted,
does the key work, and it also only works when the remote is in "A/V Receiver" mode -
not in "CABLE or DBS" mode, nor "VCR" mode, nor "DVD" mode.
So, (1) set the NetCommand remote to "A/V Receiver" mode
(2) bring up the Device Selection Menu, using the key on the remote
(3) highlight the Satellite receiver input icon (highlighted with a Yellow outline)
(4) press GUIDE on the remote, to swap the analog digital setting.

Also displays ChannelView for Antenna 1 and Antenna 2 - you may have accidentally
set the TV to get its input from the wrong Antenna.

If your TV has lost memory of its DBS source, you may have to re-teach the TV (using the remote)
that the DBS (Digital Broadcast Satellite) input exists, and to which input its connected.
Refer to "Edit NetCommand, Add an A/V Receiver", pages 39-45 of your Owner's Manual.

Jan 31, 2011 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Tv comes on for about 20 seconds then shuts off and the timer and the lamp lights flash on and off


is a inverter board defective, and shutdown auto. needs to replace inverter board. send to repair.

Feb 14, 2010 | GRY Viore RPT50V24DHD 50" HDTV DLP TV

1 Answer

My maxent TV has no picture and no sound


If an LCD TV has sound but no picture do the following:

Use the source button to ensure that source is not set to the wrong input.

Try unplugging power cord for ten minutes, to ensure it is not a setting problem.

Check all the video cables at the back of TV.

Check Light /Color settings.

If problem persist and does not depend on external receiver or settings, then it is likely an internal fault.

If it has sound but no picture then one of the following parts is faulty, and must be tested and replaced:

The inverter is the high voltage board that provides variable power to the backlight lamp. This is the most common. When inverter is faulty you can get no picture, or a very dim picture that can only be seen by pointing a torch light with a 45 degree angle on the LCD surface from very near distance.
The inverter must be tested by reading voltages with a multimeter.

The LCD ribbon cable/LCD display and connectors.
This is quite uncommon, but happens. If the TV had been hit or moved the LCD cable may have slipped out, or the LCD connector may be damaged.

The LCD controller board.
This is the board that controls the video signal, it is difficult to test, as there is need to read determined values on IC pins. To test this board you need to purchase a service manual and follow the troubleshooting diagrams on service manual.

Input/Output Signal boards.
This are the boards where you connect the video and audio cables, if a signal board is defective, then you may get no picture on particular inputs located on faulty board.

If under warranty contact the manufacturer ringing the number on the user manual.

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |

May 07, 2009 | Televison & Video

2 Answers

Timer light is flashing tv want come on


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Jan 22, 2009 | Mitsubishi WL-82913 82" Rear Projection...

1 Answer

Tv won't come on


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Oct 17, 2008 | Hitachi 61SWX10B 61" Rear Projection...

1 Answer

A repair question for the RCA M50WH74S


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Aug 18, 2008 | RCA HD52W56 52" Rear Projection HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

490 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69845 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6393 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...