- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If the oven won't turn off the oven thermostat is often the cause of the problem. The electrical contacts inside the oven thermostat can weld themselves together and then the oven won't turn off. If this happens, turn off power to the entire appliance at the household circuit breaker or fuse. The oven thermostat usually cannot be tested and must be replaced if defective.
Oven Control Board
The oven control board has a set of relays that turn on and off power to the bake and broil circuits according to the customer settings and sensor input. If the oven won't turn off it could be that one of the relays on the oven control board is shorted closed, providing voltage to the heating circuit. It can be dangerous if the oven won't turn off. Don't leave the oven unattended without turning off power to the oven.
Some ovens are equipped with a relay board. This circuit board has several relays which control the switching of electrical current to the oven heat source. If the oven won't turn off it may be that one or more of the relays on the relay board have failed. If this happens replace the relay board. The relays on the board are not sold separately. ALSO CHECK THE BAKE AND BROIL ELEMENT.
A quick search of Google for an answer to my question "Turning Auto Off on a Fisher and Paykel Oven"
With little more detail from you like model and if AUTO Off as with Timer I could pin point it, i..e.be more accurate.
So if my guess is correct than it should be on the Analogue/Analog Timer Knob OR if electronic somewhere on the keypad, electronic touchscreen? pad....meaning set it to MANUAL....have you tried that?
This sounds as if the electronic clock timer is in automatic mode. It must be in manual mode for the oven to work. Turn the oven on and play around with the timer controls/buttons. When the oven indicator light comes on the clock is in manual mode.
Hello there Electronic
ovens with a digital display use a sensor to monitor oven temperature.
To solve temperature problems for these models, you may need to replace
the sensor. On some digital-display models, you can calibrate the
temperature using the key pad. See your operator's manual for details. Ovens
without a digital display often use a mechanical system for controlling
temperature. On many of these units, you can remove the thermostat knob
and adjust the knob itself to more accurately represent the actual
setting of the thermostat. If,
when you remove the knob, there's a screw on the back of it with a
small calibration plate, you can loosen the screw, adjust the plate,
then tighten the screw again. If the knob isn't adjustable, and the oven
temperature is off by more than 30 to 40 degrees, you need to replace
the thermostat to solve the problem.
hELLO THERE: on these ovens the f-3 can sometime be incorporated with the f-4 error code also so here is the code and the things to look for both ok ?
F3 - F4
sensor (circuit) (over 2700 ohms) or, shorted oven
sensor. Could be a result of: ·
on terminals ·
wire in oven temperature sensor circuit ·
solder joint on control.
power to range
and remove oven temperature sensor connector from
control. · Measure
oven temperature sensor resistance at oven
connector (take care not to damage terminals in
block) - Should
read 1100 ohms at room temperature (approx 72
degrees F). · Measure each oven
sensor lead from connector block to ground. If
for pinched or cut wire in oven temperature sensor
circuit. · Check connector
Look for deformed or corrosion on terminals. Repair
If all above is ok replace control.
First set the clock if you cant do that just press buttons till the numbers stop flashing the turn the knob with pictures to one that looks like a fan in a box that should be fan forced option the select the tempreture with the other knob