Question about Malber WD1000 Front Load Washer/Dryer

2 Answers

MALBER WD 800

MACHINE STOP SPINNING AND DRAIN WATER.

Posted by on

  • 2 more comments 
  • SCORPION1956 Feb 04, 2008

    YOU ARE GENIUS PREMM. i FINE THE CLOGG IN THE EXIT HOSE. FILTER WASE CLEAN. NOW, WHAT IS THE STANDPIPE? I DID NOT TEST MACHINE YET. i WILL LET YOU KNOW AND DEFENATLY WILL RATE. THANK YOU SO MUCH. 3:30AM.

  • SCORPION1956 Feb 05, 2008

    My machine exit hose wase connected to the sink drain pipe ( like T shape) and gris and other kitchen staff cloged the exit of the wosher waste hose. I eliminate ths with snake, hot and cold water. I was about to buy new machine - and yor advaise and 30 min. of my work solve this. I thank you one more time and oppreciate yor timly wise and simple respond on my problem. Wish you luck and G-d bless. Scorpion and family.

  • SCORPION1956 Feb 05, 2008

    My washer is in the kitchen (in dishwasher place) connected to the sink drain pipe ( T ) so I do not have stand pipe. Thanks for explanation. Hope this will halp to other people.

  • Anonymous Mar 18, 2014

    Is it normal for water to rush out on trying to clean the lint trap at the front bottom rt of the machine? I love this machine but think there must be a better way to clean the lint trap. Also how often should this be done on the Malber WD 1000?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to find electrical drawing for washing mashine Malber WD 800?

Posted on Jun 06, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped. Click on 'thanks for trying' if not helped, your prob will be back for someone else to solve.

Posted on Feb 04, 2008

  • prem mathew Feb 05, 2008

    Thanks for the nice comment....the standpipe is the pipe which is on wall behind the machine, height about 3 feet, some people have this, others direct the waste hose into a sink or washbasin.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get the water to drain in the Malber WD100 washer/dryer combo?


Hi. I''m assuming you are referring to a WD1000.
To initiate the drain cycle: Rotate far right knob CLOCKWISE to Position 4. It may take 30-45 seconds to recognize the knob's new position, but then it will begin an 11 minute Slow Tumble/Pump Out cycle. During this cycle you'll see the internal drum slowly rotate CW for 60 seconds, pause, then rotate CCW for 5 secs - then repeat. All this time the pump will run and you'll hear water running down the drain. When you hear no more water you can rotate same knob to "straight up", and stop the machine. To turn power off, press the rightmost button.

Sep 21, 2014 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Excessive vibration during spinning


I think it should be normal.One of our washing machines does it too.No problem so far.

Aug 05, 2012 | Malber WD1000 Front Load Washer/Dryer

2 Answers

I have malber wd 800, Washer works all right, but doesn't drain water properly. 2ndly Dryer does rotate but no heat..doesn't dry the clothes.


Hi,
Here is a tip that will help you with that...

Washing Machine does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you have a gas dryer2_bing.gif.
The most common problem with a gas and no heat is the ignitor going bad...

Here is a tip that I wrote about that problem...
Gas Dryer2_bing.gif not Working Gas Dryer2_bing.gif Not Heating
http://www.fixya.com/support/r4398592-gas_dryer_not_working_gas_dryer_not

If your dryer2_bing.gif is electric2_bing.gif..
There could be a number of different problems...
Check out this tip that I wrote about this problem...

Dryer2_bing.gif Troubleshooting2_bing.gif Electric2_bing.gif Dryer won t Heat
http://www.fixya.com/support/r3866345-dryer_troubleshooting_electric_dryer_won

heatman101

May 06, 2010 | Dryers

2 Answers

MALBER WD 800 Features


I have a manual if you wold like a copy.. I can fax it to you
Heartcracker6@yahoo.com

Mar 31, 2009 | Malber WD1000 Front Load Washer/Dryer

2 Answers

Malber P21 works 3 times slower than normal; I am afraid it will just stop.


I have a Malber P21 the door was open and not turned on and it filled with water till it overflowed onto floor....any ideas?

Dec 02, 2008 | Malber P21 Front Load Washer

1 Answer

Dry cycle


Try setting the washer dial to the stop setting at the end of setting number 4 then set the dryer timer and turn on the machine.  This works for mine to get the dryer to run by itself.  It should begin about 30 seconds later, when the door locks.  Hope this helps.

May 13, 2008 | Malber WD1000 Front Load Washer/Dryer

2 Answers

MALBER WD 800 WASHING MACHINE USER MANUAL


Sorry, I don't know what your question/problem is. If you need a manual, I have one for WD 1000, but not for WD 800.

May 02, 2008 | Washing Machines

1 Answer

No final spin


I haven't experienced that problem, but is it possible that the machine becomes unbalanced with the spinning load and then aborts the spin, so it doesn't finish? Has the machine been properly leveled during installation?

Apr 09, 2008 | Malber WD1000 Front Load Washer/Dryer

2 Answers

Malber WD800 - Will not fill


my malber sounds like a jet plane lifting off at various points during the cycle, when it's spinning, I am pretty sure.  Any ideas?

Mar 21, 2008 | Washing Machines

Not finding what you are looking for?

Open Questions:

See all Malber WD1000 Front Load Washer/Dryer Questions

Malber WD1000 Front Load Washer/Dryer Logo

Related Topics:

923 people viewed this question

Ask a Question

Usually answered in minutes!

Top Malber Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

Jason Harris
Jason Harris

Level 2 Expert

256 Answers

Are you a Malber Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...