Question about Panasonic SC-AK220 CD Shelf System

1 Answer

AUDIO PROBLEM THE UNIT IS NOT FUNTION CMPLETELY

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Uncrew the unit replace fuse.

Posted on Feb 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I Have a Sony LBT LX5 Hi Fi System, the front display panel does not light-up anymore, but the machine still works.


Hello
The display of these type of sets are of vaccum type one, which will have a heater filament inside. Like any other vaccum bulbs, the filaments of these part may get opened; and can be said damaged. It is a glass vaccum unit, can be located just behind the display window, will have to be replaced as a unit. OK.

Jan 04, 2012 | Audio Shelf Systems

1 Answer

I have wac700, cd stacked in cd driver. How can i remove side speakers and open the device?


1. Unplug the two audio connectors from the base of the main unit and free the external speaker cables.
2. Press in each of the bottom clips towards the centre of the main unit and lift the speakers up and out of their mounting key-holes.
3. Remove the six recessed T10 screws holding the back of the unit on.
4. Unplug the two ribbon cables between the main unit and front panel.


The CD mechanism should now be accessible and it any trapped CDs can be removed.

Oct 08, 2011 | Philips WACS700 Shelf System

1 Answer

No sound coming from main stero


If the speaker wires are connected properly to the main unit and the unit lights up then the problem is a bad audio output ic, a common issue with Book Shelf Systems. The only solution is have it replaced with consideration of cost in mind.

Sep 07, 2011 | Audio Shelf Systems

1 Answer

How do you change stations on fisher da350 no buttons on the radio will change the radio station


Change to Tuner using the Funtion button. Continue to press the MEMORY button until it starts to scan the frequencies.

Jul 19, 2010 | Fisher DCS-DA350 Shelf System

1 Answer

I would like to plug in the sound of my television set to the panasonic SC-PM08. I tryed to do that by plugging in the tulip plugs in the "aux" connections, but no sound comes out. what could be the...


You mention "tulip plugs"! are you referring to your RCA jacks in the back of your unit? That is what the 7 inputs are to the right of your speaker connections.
When you hook your "stereo TV" to your external sound unit
you need to run your cables to your aux input from your audio out jacks on the back of the TV. Once this is done you need to configure your TV and your sound unit to work with each other. You need to go into your TV settings and tell it where to send the audio to. If you hooked into the front audio output then you need to pick that selection. If you hooked into the back audio out you need to pick that selection. Once you have completed that you need to tell your sound unit where to pick the sound up at. If you plugged into the aux then put your sound unit on aux. If you have more than 1 aux pay attention to what aux your TV is coming in on and set your sound unit accordingly.

Mar 09, 2010 | Panasonic SC-PM08 Shelf System

1 Answer

Hooking up to tv


Check any 'Audio In' pins at rear of hifi unit and hook 'TV Audio Out' pins there and select Aux or Video input to have TV sound in this unit.

Feb 03, 2009 | Sony MHC-RG70AV CD Shelf System

1 Answer

SONY AUDIO MODEL HCDZX50MD


Disconnect the audio output IC from the board an listen to hear if the output relay click, if it does the audio output is faulty replace it..

Aug 08, 2008 | Sony Audio Shelf Systems

1 Answer

Unit turns on, then clicks off with a "protect" message


You have a bad speaker on this unit or the audio output circuit is in need of repair. Try to disconnect all of the speakers and then turn on the unit. If it still stays in protect, you will need to have this unit serviced, unless you understand how these solid state circuits work. If the unit does come on without the speakers, turn off the unit and add one speaker at a time until the unit will not turn on. Disconnect that speaker and have it checked out or have the wiring checked out. Good Luck

Jul 14, 2007 | JVC FS-G5 CD Shelf System

1 Answer

Power turns off immedietly


Yeppers, when you where changing out those speakers, you shorted them and that in turn blew out the audio output IC inside this unit. This will require you to disassemble the unit, locate the blow output IC abd unsolder it, get a new audio output IC, put some heatsink compound on the back of the new IC, resolder the chip and reasassemble the unit. But before you turn on the unit, double check those speaker wires again to make sure they are not shorted as if they are, even one tiny strand, this unit will blow the IC again. Never work the speaker on any solid state electronic amp when they are plugged in and on. Good Luck

Mar 27, 2007 | Aiwa NSX-A115 Shelf System

Not finding what you are looking for?
Panasonic SC-AK220 CD Shelf System Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Audio Shelf Systems Experts

Jonathon summesfield

Level 2 Expert

284 Answers

 Grubhead
Grubhead

Level 3 Expert

4593 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Panasonic Audio Shelf System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...