Question about Heating & Cooling

1 Answer

Midea Hi Im new to China and it is cold here now how can i tell if my unit has a heat device on it since everything is in Chinese

Posted by on

  • rrsadler737 Feb 02, 2008

    I dont have the heat Icon on my remote thanks though, I do have a small heat symbol on the front of my unit inside the a small blackened strip. ?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 236 Answers

If your unit is remote control try to check the mode icon.

midea - 3305362.jpg

Posted on Feb 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi slit air conditioner model MSZ-GA80VA I turn on and turn off cauting out door unit fuse blown I replaced still The fuse is blow is the out door air con unit Note.unit in door stop not inpos


turn off everything electrical in house and retry with good fuse or breaker if still blows unit needs repair possible shorted capacitor? if it runs it may need to be on its own circuit dedicated to it alone

Jan 05, 2017 | Mitsubishi Heating & Cooling

1 Answer

I have a older Carrier heat pump, model 38YKC060. Does anyone know how cold it will continue to work at?


Heat pumps are of little or no value at temps around 40 degrees or below. And if you use the strips it will cost a small fortune if you have relatively high electric rates as most folks do.

Jan 04, 2017 | Heating & Cooling

2 Answers

Replaced ac unit with new compressor. Fires up as usual but compressor wont start.No fault code coming on controller. Whats the problem?


possible causes include
excessive gas
low gas
relay not working,
faulty thermostat
faulty start/run capacitor
bad circuit board

Jan 03, 2017 | Heating & Cooling

1 Answer

How do I fix my electric heater


  • sounds like the sensor or bulb that tells it to start the blower is defective/ im not familiar with your unit but this seems the most logical answer most furnace will not turn the blower on right away usually 90 seconds after the ignition but will also run longer to exhume any dangerous carbon monoxide. Electricic heaters are different. What type of unit do you have

Dec 25, 2014 | Heating & Cooling

1 Answer

Electric Furnace stopped running


You have one of two problems. Either the capacitor for the motor has failed or the motor has failed. I would turn off the power to the unit and see if you can locate the capacitor and remove it. An ac supply or electrical supply house can match up the capacitor. This is relatively inexpensive. Otherwise you will need a new motor.

Nov 11, 2014 | Heating & Cooling

1 Answer

How do I get my radiators to start working?


ch1 indicates wirless thermostats? check the thermostats in the room have fresh batteries. this type can be wired but may be running on batteries you have to use a screw driver from below to open the unit. if you dont have a manual here is a link.
http://www.manualslib.com/products/Danfoss-Randall-Tp5000-Si-Range-2781091.html
i hope this helped

Oct 22, 2014 | Heating & Cooling

1 Answer

My termost set to a/c, the fan auto, blow very well, but when I switch to heat and the fan auto, doesn't work, but if I put fan on work why?


the thermostat says to call for heat buildup in the work if its not cold enough the thermostat won't call for heat and I won't go on but when it gets cold and the thermostat set to the temperature you want or hire someone that doesn't cycle

Oct 12, 2014 | Heating & Cooling

1 Answer

Household steamer not heating at all


Well, first thing, just hook up service water and turn it on so the water heats up. Leave it long enough for water to get hot. If water doesn't get hot like should, then heating unit is malfunctioning. If it is getting hot after a while, you pull the handle trigger and water comes out, you have to wait long enough for the hot water to get to the head/trigger for it to go into the nozzles. If it was working ok before, and you were waiting for the water to heat, then then it should be working fine. Tell me what is happening if you wait for water to heat and get to the nozzles. I'm right here at my computer and we can get this thing going if the heater unit is good. Regards, Rigger.

Oct 07, 2014 | Heating & Cooling

1 Answer

Why can't I lower my honeywell 8500 below 67 on cool?


With a two story house you have to be aware that cold air flows downwards so any cold air coming from an ac unit will flow downstairs( normally down the stairway) so unless you can close off the down stairs then the up stairs unit will be cooling downstairs as well. Ac units have a thermostat located in the air intake and it cools until the cold air has risen to that point. In effect the space above the ac unit will be hotter than the floor. Knowing how they work ,you can see that the upstairs unit will never reach the set temperature because the cold air is continually heating from the house and will never get to the top thermostat.
So your solutions are
1-- fit controls that restrict the cold air from leaving the upper floor (Doors)
2--don't run the upper ac unit unless you are living up there (waste of money
)3 place an ac in each upper room and keep the room door closed

Aug 12, 2014 | Heating & Cooling

1 Answer

My deLonghi dehumidifier no longer dehumidifies. The device appears to be functioning OK but is not taking a drop of moisture into the tank. Previously, it filled in about 48 hours.


Hi, Soorry for the delay in the respones but I was stuck in a factory job the last few days.
When this happens usuall either the compressor is not running or the unit is packed with dirt. Can you tell me if you hear the compressor kicking on? I will look up this model and cover all the bases for you. The sysytem is slow on resposnes right now but I will keep on top of this with you till se get it going. Alsocheck the tank for a pluggage in the drain tube.

Feb 06, 2012 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2096 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...