Question about Siemens Gigaset 2415 Cordless Phone

1 Answer

Registering a base station of Siemens Gigaset 2415 Cordless Phone

I have this set but when i switching on this set i get a message"Please Register", but i m unable to regiater my base station as i dont know the base station pin of manufacturer please give me that pin so that i can register my base stations

Posted by on

  • 1 more comment 
  • nurse11751 Dec 31, 2008

    siemens 2415 says please register how do i register

  • Anonymous Mar 12, 2014

    Base set registered Hand sets will not register

  • Anonymous Mar 14, 2014

    I have disconnected the batteries and the base station to reset but no change

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 106 Answers

To register your handset to that base station, you must put the base station in registration mode at the same time you put the handset in registration mode. This is how you do it. At the handset you push OK when it asks you to register. If it asks you for the pin enter 0000 (factory pin) and push OK. The handset should say "registering base 1". Then at the base press the page/reg key down until it flashes (its to the immediate right of the cradle where you rest the handset for charging). That puts the base in registration mode and now its looking for the handset and vise versa. Now watch your handsets display. If it asks to to select an intercom number, then push ok and your done. If it says "invalid pin" then you need to reset your pin on your base (thats a different problem see below). If the handset times out and never registers, you need to repeat the process a couple times, you may have a bad base or it needs to be defaulted. If you need more help you can download a manual for free or get free technical help at the link below.
http://www.barclayent.com/manuals/Gigaset%202415%20User%20Guide.pdf

If you need to default your pin, you can do so but it will default the base station to factory settings. To do so remove the power from your base, hold your page/registration key down, and apply power back to the base. Count to 15, then let off the key. Turn off the power, count to five, then apply power again and follow the steps again to register the handset and you will need to reregister every handset that was previously running on it.

Posted on Feb 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PROBLEM WITH THE BASE GIGASET A120


Thank you for these instructions. I have Siemens geigaset A120 with three handsets and one of the handsets stopped working about a year ago and my previous tries att registering it at the base station had failed and I was about to give up and buy a new set for 80 Euro, but I decided to give i one more try at registering and it worked the third time around. So do not give up. When one your hand sets stops working (no dial tone and can not call from it) try re registering as described above.

Nov 23, 2012 | Siemens Gigaset A120 Single Dect Cordless...

1 Answer

PURCHASED USED SIEMANS 8800 HAND SET ,REPLACED BATTERY,AND RESET PIN TO DEFALT 0000, PHONE FLASHING "SEARCHING" .HOW DO I GET THE HAND SET TO SYNK UP TO THE BASE STATION?


You need to register the handset to your base to get the phone to work to do this follow the steps in the manual. If you do not have the manual go to the link below and scroll down to product detail then click on the blue product manual.

Gigaset-Accessory-Cordless/dp/B00005UFDR">http://www.amazon.com/Siemens-8800-Gigaset-Accessory-Cordless/dp/B00005UFDR

Or look below to learn how.


    
jyackle5_61.jpg

Jun 03, 2011 | Siemens Gigaset 8800 Cordless Expansion...

1 Answer

My Siemens gigaset A 490 cordless phone is showing Register HS what i have to do pl advise


To register the Gigaset handset, you need to have the handset near the base. Press and hold the Register/Paging button on the base for 3+ seconds (it's hidden by the handset when on the base). A shorter press of the button will activate the Paging feature. Then within 60 seconds of pressing the Register button on the base, press Menu and select Settings. Press OK and go to Handset. Press OK and then select Register HS. Enter the base PIN (default is 0000) and then press OK. (Use the up/down arrows to navigate the menus.) You will see Registering flash on the display of the handset for approximately 1 minute while the registration is processed.

The manual for the Gigaset A490 is available here: http://gigaset.com/medias/sys_master/A31008-M2200-R301-2-3S19_en-fr-es_USA_CAN.pdf . If you need it in another language (or country), start here: http://gigaset.com/hq/en/product/GIGASETA490.html?tab=manuals .

I hope this helps.

Cindy Wells

May 26, 2011 | Siemens Gigaset A490 Twin Cordless Phone

2 Answers

My handset is displaying register HS. kindly provide me the required support to reslove the problem.


Hi,

Please follow this procedure to register your handset

1. On the base station: press and hold the registration/paging key for min. 3 sec.


2. On the handset: within 60 sec. of pressing the registration/paging key;

Select MENU then Settings then OK then Handset then OK - Register HS then OK -


Enter the system PIN of the base station (the default PIN is 0000). Then press OK.


Registering now flashes in the display.

Registration takes approx. 1 minute to complete.

Thanks for using FixYa. Please do leave a vote for the help.

Nov 25, 2010 | Siemens Gigaset A490 Twin Cordless Phone

2 Answers

Siemens gigaset 2420. how do i reset pin on desktop base corded station?


  1. I forgot the PIN number on my Gigaset 2XXX system base station. What can I do?
    Please complete the following steps to reset the system PIN on 2XXX back to 0000. On the system base station:
  • Press MENU.
  • Scroll to SYSTEM SETTINGS but do not press SELECT.
  • On the keypad, enter *65# (Star, 6, 5, Pound).
  • It will display "SYSTEM PIN RESET" and return to the idle screen.
  • Note: The base station system PIN will be reset to 0000

  1. I forgot the PIN number on my Gigaset 2XXX cordless handset. What can I do?
    Please complete the following steps to reset the cordless handset PIN on the 2XXX back to 0000.
  • Press MENU.
  • Scroll to MOBILE SETTINGS and press SELECT.
  • Scroll to LOCAL SETTINGS and press SELECT.
  • Scroll to CHANGE PIN and press SELECT.
  • On the keypad, enter *65# (Star, 6, 5, Pound).
  • Note: The handset PIN will be reset to 0000


Jan 05, 2010 | Siemens Gigaset 2420 Cordless Phone

2 Answers

Keeps going back to Register HS


Thats because there are too many handsets registered to base OR it can't find the base. Did you set it to register then pressed the little tab in on the bottom of the base? You have to hold tab down and keep phone close to base (a foot or so). If handset goes out of reg mode, you have to put it back in, then quickly press base tab down again before it stops.

Dec 17, 2009 | Siemens Gigaset A140 Cordless Phone

1 Answer

Getting a new mobile in the registration mode with my Gigaset 8825 base station.


You need to register the handset to your base. Its easy, but first you need to clear the setting on the handset. Do this by pushing Menu, scroll to base system settings, push OK, then scroll to Base station 1, push OK, then scroll down to deregister, push OK twice, then press End. The handset should now say "please register", of which you can press OK, enter your pin or 0000 and the display should be flashing "registering base station 1". Now quickly, at your base push Menu, scroll forward to system settings, push select, enter your pin or 0000, then select. Push select again and the display should say "registering HS". Now, both displays (base and handset should say registering), keep your eyes on your handset display, once it "shakes hands" with the base it will prompt you to select an intercom number, you can just push OK. If you have problems, repeat the steps or you can download a manual for free at www.cordlessrepair.com

Oct 18, 2007 | Siemens Gigaset 8825 Cordless Phone

1 Answer

Siemens 8825 gigset 2 line phone


If your system was working fine, and it all of a sudden started doing this, it sounds like your base has taken a surge of some kind. Your base needs replacing. You can try re-registering the handsets, but from my experience the problem is fatal. Now if this is a new installation and the handsets never work yet on the base, you just need to register them. You can download the manuals or get tech tips at Siemens website, gigaset FAQ pages.

Sep 04, 2007 | Siemens Gigaset 8825 Cordless Phone

Not finding what you are looking for?
Siemens Gigaset 2415 Cordless Phone Logo

1,944 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

Cindy Wells

Level 3 Expert

4951 Answers

Are you a Siemens Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...