Question about GE DCVH515GF Gas Dryer

1 Answer

Error code e 61

After a brown out my dryer is displaying e 61 on panel--this occured a month ago and repairman said he "reset " the board but this time he wants to replace board without attempting to reset--dryer has worked fine since last reset

Posted by on

  • 1 more comment 
  • dpreyn Mar 16, 2008

    I had a power surge and now my G.E. dryer is showing Error Code 61. How do I reset it? I have turned the breaker off and on but this doesn't fix it. I get nothing when I push the buttons. I have model# DBVH512EFOWW

  • Anonymous Nov 27, 2008

    My problem is the same. A brown out has caused E61 to show on the display. How do I fix it?

  • Anonymous Jan 07, 2009




1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same description , the same problem:I
had a power surge and now my G.E. dryer is showing Error Code 61. How do I reset it? I have turned the breaker off and on but this doesn't fix it.
I am JD and my e-mail is :
Thank you all¡

Posted on Sep 08, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

TagakiLP Tankless Water Heater is less than 6 months old. I am getting error code 61. Opened the front had some moisture and dryed it with a hair dryer. Still getting code 61. Suggestions?

Tankless water heaters are the worst. Get a standard gas water heater, they are more reliable. The blower motor for the exhaust is not functioning, could be defective control board that controls the motor and coil temp. Once this starts the problem resurfaces again and again . I know the are space savers , supposed to be energy savers, and give you limitless hot water,....but they are not all that reliable . Most new homes are being built with them.. My preference is standard tank heater.

Dec 12, 2017 | Dryers

1 Answer

My Wascomat TD77 dryer keeps shutting down after 5 minutes and shows E 14. What is wrong with it.

Taken from the following:
This is for a different model, but the codes are likely the same.
It is related to non-ignition of gas. You may need to switch on your gas supply, or service your ignition coil.

Resetting gas error
When the ignition control fails to detect a flame a error code E14 is displayed. When this condition occurs, the gas valve is shut off and the ignition control must be reset manually.

Open the operating panel and press the gas reset button on the back of the user module board for one second.
See the picture of the gas reset button section 21
NOTE! When resetting the system the dryer must operate on a program with heat and when the heat indicator is on.

Error code
Error code 14 is a normal occurrence when first starting up a dryer, since air in the gas line must be purged.

Aug 26, 2014 | Dryers

1 Answer

Error code loc

Hi Amanda, thank you for your inquiry!

An error code E61 generally means that a heater relay failure has occurred. A qualified technician would pinpoint the problem by checking the wiring for both open and short circuit across heater relay(s). If the wiring isn't the issue, he/she would need to determine whether the problem rest with the main control board. It really could be a hit or miss calculation in parts so I would personally reach out to an experienced tech that will be able to identify the precise reason.

Dec 01, 2013 | Frigidaire Electric Dryer

1 Answer

Error code E 61 shows and dryer shuts off after about 5 minutes.

Good Afternoon Melissa, thank you for your post!

Typically, an E61 error code is an indication of a short circuit. Let's try resetting the dryer by either unplugging it or flipping the household circuit breaker to the off position. It is important to wait approximately ten minutes and then turn the dryer on. If resetting the power does not correct the issue, your appliance could be experiencing a potential heater relay failure, control board issue or wiring problem. I would suggest contacting an experienced service technician to determine the precise cause.

Best regards!

Sep 29, 2013 | Frigidaire Electric Dryer

1 Answer

Fault code f-01

The "F-1" error code means a failure occurred with the electronic controls.. This could mean that wires are broken, the electronics shorted out or a manufacturer's default error shut the washer down.

Prevention/Solution: The electronic control panel needs replacement. Find your dryer serial number and search for the part online.

This is a lengthy job that usually requires a repairman unless you have dealt with and repaired dryers before. If your dryer was purchased within the past couple of years, the dryer could be covered under the warranty.

Hope this helps (remember to rate this free answer).

Jun 02, 2011 | Hotpoint Washing Machines

1 Answer

I have an rca 61" dlp tv that is about 4 years

More than likely you have a power board that is failing. Since the TV is so old I doubt it is under warranty still. I estimate it would cost you anywhere between $300-400 to repair that problem so it may be time to switch to a newer LCD TV.

Feb 28, 2011 | RCA Scenium HDLP61W151 61 in. HD-Ready...

1 Answer

Notice on dryer, a problem has been detected, call for repair. This dryer is forever doing this. Is there a way to try to reset the dryer? I just had it worked on about 8 months ago, put in a new...

Here is the instructions on how to but the machine into "service mode" so it will display error codes and we can take it from there. Post back with the error codes.

Jan 15, 2011 | GE Profile Harmony DPGT750EC Electric...

1 Answer


U-61 is a hardware error code. Usually means main board failure, however have found that a bad changer can also trigger that code since it connects directly to the main board.

Sep 21, 2009 | Panasonic DMR-ES35VS

1 Answer

Brand New Whirlpool Duet 9450 Error Code PF

This is a problem I've seen before, or something similar. I think you've got a bad connection on the neutral wire. Either in the plug or at the panel. Have electrician check the neutral wire back to the panel from the plug.

If you need further help, I’m available over the phone at

Jul 25, 2009 | Dryers

6 Answers

Kenmore Oasis dryer F40 error code

I had this same issue. My dryer would run and heat up but then stop and give me the f40. I measured all thermisters and everything was in range. The tech sheet stated that I needed to buy a new control board and I did. Same problem.
The solution was a loose connection on for p4. I took needle nose pliers and squeezed the connector to make it fit tight on the board and everything is working now.
Bottom line, expensive dryer with cheap connectors.

Nov 16, 2008 | Frigidaire GLEQ2152ES Electric Dryer

Not finding what you are looking for?

Open Questions:

GE DCVH515GF Gas Dryer Logo

Related Topics:

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dryers Experts

Dave Harrison

Level 2 Expert

114 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers


Level 3 Expert

1216 Answers

Are you a GE Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides