Question about Televison & Video

2 Answers

Thomson Wysius 32wp95E Plasma

The screen was working fine, but i was stuppid to open him up to clean some dust ,so I removed the middle plate an also removed a power cable for a half oure wich was conected in the inside of the screen.
i removed some dust on one place an conected back the cable just how i removed it, an dan i put the backpanel back on the screen an turn him on,but the tv wont show me his menu no more an jump in his collor.

3 times green,than 1 time yellow,an if i pus the remote butten he some times jumps in standby,but the collor light red is not blinking of an on like the green collor, can u help me or some one, yesterday the tv man came an tooke a look,he said he cant do nothing without a component scheme/manual( the book with all the diodes en small component on it. pplease help me or do you know wer i can find it.


Posted by on

  • 3 more comments 
  • oeka2000oeka Feb 01, 2008

    but what can i do abouth the problem,the light of the screens gos on when i turn it on,but i do not see the menu on the screen?

  • oeka2000oeka Feb 01, 2008

    can it be that when i disconnected the cable(s) the system software crasht or somthing ?

  • oeka2000oeka Feb 03, 2008

    is their still somebody who can solve my problem i did every thing on the screen (checkt cables that i disconected an conected back)??????///?????HELP ME PLEASE ,cause my father is angry

  • TVRalf Jul 27, 2008


    I have the exact same problem with the same TV. Could you help me by telling me what you did about that problem?

    Mine also does not turn on the screen and just flashes the green light tree times and then the red light. it does this over and over

    Thanks for helping

  • pabushayhw Aug 04, 2008

    my tv is blinking yellow light



2 Answers

I did what you said ,but the tv is still doing the same thing!help me

Posted on Feb 01, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,554 Answers

You should take it apart again.
And put it back together again.

Ignore the TV guy. He did not want to fix it.

Posted on Feb 01, 2008

  • Karl Whisenand
    Karl Whisenand Feb 01, 2008

    Not likely,

    you must not seated a cable correctly.

    or got cable plugged backwards

    the Cables striped side is pin 1 , and will match marked pin 1 on the board.

    A laptop guy will know how to fix it.

  • Karl Whisenand
    Karl Whisenand Feb 03, 2008

    You will find that there are very few folks that actually work on lcd
    panels, and fixing one remotely through this forum is very unlikely.

    I am one of the few real electronic techs even in my city (Austin)

    I fix to the chip level,

    Put an ad on to see if anyone in your area has the tools and knowledge to look at your panel.

    As for a service manual most electronic makers don't issue them except inhouse and to service centers.

    As you have done your best to fix it , it's time to see about a
    professional in the lcd panels. (thats not a tv repair guy usually)



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Thompson Wysius 42" plasma woes

did u try a different connector of cable?

Jun 12, 2008 | Thomson 30LCDB03B 30 in. HDTV

1 Answer

Thomson wysius 42 plasma sound

It sounds like its back-light inverter board has damaged. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy Pull up older posts. Surf the site with patience.

Apr 17, 2014 | Televison & Video

1 Answer

I am trying to connect my laptop to my thomson wysius plasma through the tuner box,i get an error message NON supported format,i have changed the resulution to 800 by 600 but still no joy,any help would be...


The issue is with resolution and also with REFRESH RATE! Hence 60,75,100 HTZ try setting to defualts.

The TV is just trying to protect itself from harmful resolution or rfresh rates that could damage the TV itself. When in doubt set it to the lowest settings, and try it again.

Thanks and please do be considerate when your passing trew fixya to leave postive feedback and ratings for the experts that tried to help you today.

Btw, I’m available to help over the phone in case u need at

May 26, 2010 | Televison & Video

3 Answers

A black line running verticall down the middle of

There is no invertor board on a plasma tv. The fault is the X address buffer board. This is located on the bottom of the screen and runs horizontally the whole width of the screen. If you remove the heatsink plate that covers the x address boards and you need to look at the screen ribbon at the same position as where the bar is (in the middle).Vary gently lift the Xbuffer ribbon lock and gently take out the ribbon.Clean the contacts very carefully with a fibre pen or an electrical cleaning fluid.Insert ribbon back and heatsink and check.Here is a picture of the board and ribbon

a 1 inch bar is associates with 1 ribbon fault. So if the bar was 3 inches in from the left of the screen, the faulty ribbon will be 3 inches in from the right working from behind the TV. If cleaning dont cure the fault, then the Buffer IC will be blown and order a new centre buffer board (you can buy off Ebay)

Feb 17, 2010 | LG 42PG20 42 in. Plasma HDTV

1 Answer

Is it hd

Strictly speaking to be HD Ready a TV must fullfill 2 things:

1. Have a Screen Resolution of at least 1024 x 768.
2. Have at least 1 HDMI Socket.

Your TV has neither of these, so it is NOT HD Ready, however, it will still be more than capable of showing SKY HD, and it will still look very nice indeed.

I would need a list of the connections on the rear of the TV to tell you which cable to buy, but:

If it has DVI, then a simple HDMI to DVI cable will do for the video.

If it has component, i.e Yb, Yr etc then you will need a more expensive HDMI - Component Video cable.

But otherwise, yes, SKY HD will work fine.

I hope this helps.

Mar 28, 2009 | Televison & Video

2 Answers

Thompson Wysius 42

Don't know the answer to your problem but I found a lot of useful information here:

Jul 04, 2008 | LG 42PX4DR 42 in. Plasma TV

1 Answer

My thomson wysius plasma tv comes on but the picture fflashes on and off ive connected pc to screen and is ok,so is it something to do with tuner box.?

You can also try to use the audio and video inputs to narrow the failure down to the tuner.
Let me know if you need further assistance.

Apr 15, 2008 | Televison & Video

2 Answers

Super Ikonta 530/2 B Speed setting not working. ClAing camera.

If you want a manual you can get it here
Read this and since its a simple problem you will get all you want to know!

Oct 03, 2007 | Photography

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

1,113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75767 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

81342 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides