Question about Frigidaire Affinity ATF7000E Front Load Washer

2 Answers

Frigidaire Washer - pressure sensor

Due to electrical problems we have had to replace the control board in our washer. We get an error message: Pressure sensor not communicating with control board. According to the manual, we need to to replace the control board. We've just put in 2 brand new ones - big control board and the little one to the left. Any ideas where to go from here?
Thanks!!!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

I agree with the pressure switch could have been this in the first place? But also when you replace the boards they may need an eeprom program as they may be a blank un programed board

Posted on Nov 02, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,003 Answers

I WOULD SAY REPLACE THE PRESSURE SENSOR IF BOTH CONTROL BOARDS HAVE BEEN REPLACED

THE MOST ECONOMICAL PART ASSOCIATED WITH THE CONTROL BOARDS ESPECIALLY AFTER HAVING ELECTRICAL PROBLEMS IS MORE THAN LIKELY THE PRESSURE SENSOR it may have BLOWN ALSO

Posted on Jan 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F35


The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor. This error code can be caused by a problem with the air pressure tube between the bottom of the washer tub and the analog pressure sensor. If you are able to unplug the washer and check this air pressure tube, you may be able to resolve this problem. The analog pressure sensor can be accessed by pulling off the top panel of your washer. Remove the screws at the very back of the top panel and then pull it back slightly and then up and off of the washer. The analog pressure sensor is Key 38 in the first image below. With the washer unplugged, check the connection of the air pressure tube to this component. Check the entire air tube down to its connection to the bottom of the washer tub. You will likely need to remove the back panel of the washer to check the entire air pressure tube. If you find a kink, tear, hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor. If the problem still exists after replacing this component, then the main electronic control board for the washer will need to be replaced. Here is the pressure sensor you can order.

Oct 27, 2012 | Kenmore Elite HE5t Washer

1 Answer

Error code 31


Hello Elizabeth - Typically error code E31 indicates that the pressure sensor is not communicating with the main control board. I would suggest contacting a professional to inspect the wiring between both parts. Depending if the wiring is defective or correct might have to replace the pressure sensor. If it does not correct the problem, the unit may possibly have a defective control board and will need replacing.

Oct 01, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Error code 32


Hello Lance - Error code 32 for Frigidaire models means there is pressure sensor calibration problem. This will need to be checked and a repair performed by a technician since they must do the following: inspect the wiring between the pressure sensor and the main control board. Correct the defective wiring and/or replace the pressure sensor or main control board.

Sep 16, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

E10 error code on Frigidaire affinity how to repair it


Your fill time, water fill time, is too long. Have a professional complete the following:
. Is the incoming water flow normal? Yes, go to step (4). No, go to step (2). 2. Are the incoming water faucets turned on? No, turn water faucets on. Yes, go to step (3). 3. Is the incoming water pressure above (30) psi? No, have customer correct pressure problem. Yes, check for kinked or blocked incoming water hoses, clean incoming water screens. If problem still remains, replace the water inlet valve assembly. 4. Does the fill water continue to enter the washer? Yes, go to step (5) no, go to step (6). 5. Remove power from washer. Did the water fill stop? Yes, go to step (6). No, replace the inlet valve assembly. 6. For Better models, check the electronic pressure sensor. For Good models, check the pressure switch. Pressure sensor checks good. Go to step (7). Pressure sensor checks incorrect. Replace pressure sensor. 7. Replace the Main Control Board

Aug 16, 2012 | Frigidaire Affinity ATF7000ES Front Load...

1 Answer

Receiving code F35


The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor. This error code can be caused by a problem with the air pressure tube between the bottom of the washer tub and the analog pressure sensor. If you are able to unplug the washer and check this air pressure tube, you may be able to resolve this problem. The analog pressure sensor can be accessed by pulling off the top panel of your washer. Remove the screws at the very back of the top panel and then pull it back slightly and then up and off of the washer. With the washer unplugged, check the connection of the air pressure tube to this component. Check the entire air tube down to its connection to the bottom of the washer tub. You will likely need to remove the back panel of the washer to check the entire air pressure tube. If you find a kink, tear, hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor. If the problem still exists after replacing this component, then the main electronic control board for the washer will need to be replaced.

Jul 10, 2011 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore Elite 46742 washer will not wash. It starts to fill and then SUDS or F35 appears on screen. It will not move through the cycle.


The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor. This error code can be caused by a problem with the air pressure tube between the bottom of the washer tub and the analog pressure sensor. If you are able to unplug the washer and check this air pressure tube, you may be able to resolve this problem. The analog pressure sensor can be accessed by pulling off the top panel of your washer. Remove the screws at the very back of the top panel and then pull it back slightly and then up and off of the washer. The analog pressure sensor is Key 38 in the first image below. With the washer unplugged, check the connection of the air pressure tube to this component. Check the entire air tube down to its connection to the bottom of the washer tub. You will likely need to remove the back panel of the washer to check the entire air pressure tube. If you find a kink, tear, hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor. If the problem still exists after replacing this component, then the main electronic control board for the washer will need to be replaced.

Jan 23, 2011 | Kenmore Front Load Washer

1 Answer

What is F35


The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor. This error code can be caused by a problem with the air pressure tube between the bottom of the washer tub and the analog pressure sensor. If you are able to unplug the washer and check this air pressure tube, you may be able to resolve this problem. The analog pressure sensor can be accessed by pulling off the top panel of your washer. Remove the screws at the very back of the top panel and then pull it back slightly and then up and off of the washer. The analog pressure sensor is Key 38 in the first image below. With the washer unplugged, check the connection of the air pressure tube to this component. Check the entire air tube down to its connection to the bottom of the washer tub. You will likely need to remove the back panel of the washer to check the entire air pressure tube. If you find a kink, tear, hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor. If the problem still exists after replacing this component, then the main electronic control board for the washer will need to be replaced.

Jan 09, 2011 | Kenmore Front Load Washer

1 Answer

I have a Kenmore Oasis HE top load washer; purchased it in 2006 and I had the foresight to purchase the master protection plan & extended warranty. I have had SEVERAL repair calls for a variety of...


The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question!!!!!!

Jun 14, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Our washer keeps showing an error message F1? If


The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question!!!!

Jun 07, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

E20 error message


replace the control panel or have it repaired,there is no e20 listed as a trouble code,so it needs to be replaced.

To clear latest stored error code:

Place the control into Diagnostic test Mode.
  • Turn the program knob clockwise 9 clicks from the Start Position. The control will signal the last error code.
  • Press and hold the Options and Pause Cancel buttons for 3 seconds. The code will be cleared.
  • Exit Diagnostic Mode to return the washer to normal operation.

Error code - Fault condition

E11 Fill time too long.
E13 Water leak in tub or air leak in air bell.
E14 Reed switch.
E21 Water not pumping out fast enough.
E23 Drain pump relay on control board failed.
E24 Drain pump relay on control board failed.
E31 Better models. Pressure sensor not communicating with control board.
E35 Better models. Pressure sensor indicates water overfill.
E41 Control board thinks the door switch is open.
E42 Door remains locked after cycle is completed.
E43 Control board problem.
E44 Control board problem.
E45 Control board problem.
E46 Control board problem.
E47 Board thinks the door PTC circuit is open in spin.
E48 Board thinks the door PTC circuit is closed.
E52 Bad signal from tacho generator.
E55 Motor overheating.
E56 High motor current.
E57 High current on inverter.
E58 High current on motor phase.
E59 No tacho signal for 3 seconds.
E5A High temperature on heat sink.
E5B High temperature on heat sink.
E5C High temperature on heat sink.
E5D Communication problem.
E5E Communication problem.
E5F Communication problem.
E67 Input voltage on microprocessor incorrect.
E75 Better models only. Water temperature sensor circuit.
E76 Better model only. NTC temperature for the cold water valve over the limits.
E95 Communication error.
EB1 Incoming power frequency out of limits.
EB2 Incoming line voltage above 130 VAC.
EB3 Incoming line voltage below 90 VAC.
EF1 Clogged drain pump.
EF2 Too much soap.

Apr 22, 2017 | Frigidaire ATF6000ES Front Load Washer

Not finding what you are looking for?
Frigidaire Affinity ATF7000E Front Load Washer Logo

Related Topics:

700 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...