Question about JVC AV-48WP30 48" Rear Projection Television

2 Answers

Convergence Resistor Hitachi 50DX10B

Hi

I have a blown RK46 half watt resistor (faded colors) in the convergence pannel. I cannot read the coded colors. If anyone help me to send the value of it or email the schematic will help me alot. Thanks

Sam

Posted by on

  • Anonymous Feb 09, 2008

    Hi



    Ihad replaced the rk46 resistor and stk 392-150 ics in the convergence panel of Hitachi 50dx10b. Still there is a very little red and green shadow around the picture. The picture is better than before excexpt it shrink from the sides, top and bottom looks like a cinemascope thing. some one can help me to locate the filtration capacitor in vertical and horizontal cct.. I am not sure about c-615 (25v-2200mfd) if it is not the right one can i get the help on this. Thanks in advance.



    Sam

×

2 Answers

Hi Terryfic

I had replaced the 2.2 ohms one watt ressistor rk46 in the convergence panel of hitachi DX5010B tv. Little better then before except the red is out of wack. Darkloard1 told me to check the filtration capacitor in the horizontal and vertical cct.
I wanted to make sure C615 (25v-2200mfd) is the filtration capacitor if i am wrong please guide me for the right one. The crt. R/B/G can I dicharge 200v by shorting pins p8x1 and p8x2 after shorting these pins I measured the voltage in all three crt. was 0 volt is that enough to work in that area.

Posted on Feb 05, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers

2.2 ohm 1 watt...................................T.

Posted on Jan 30, 2008

2 Suggested Answers

  • 899 Answers

SOURCE: Convergence Resistor Hitachi 50DX10B

rk46 should be a 1.8 1w

Posted on Oct 30, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Convergence problem


If you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over 2350 posts now. All are related to electronic equipment repair help. If you check the site in Timeslide option, which can be selected from the dropdown list at the top left side of the display window, it will make search easy. Details about convergence adjustments have been described with illustrations.
http://electronicshelponline.blogspot.com/

Apr 22, 2013 | Hitachi 61SWX10B 61" Rear Projection...

1 Answer

How do you fix the color to a model 43fdx11b hitachi


Hello!you mean: colors out of convergence? nothing you can do about that, unless you replace 2 convergence amplifiers I.C. chips, plus all those burned 1 watt low ohms resistors with exact values, which only could be obtained via service manual or schematics. After resistor is burned, there is no way to read color code properly, due to partial evaporation of pigments. this is a "pro" job. If you try or tried, already to converge those "stubborn" crosses, there is more to do, even after you removed and replaced two 20 pin I.C. chips, soldered dead into sweep module, plus located and replaced resistors with precise values, you need to get your settings back to normal, by going into "factory service mode' or, at least into "convergence alignment" menu and fight with those crosses!Don't forget the white "****"! Otherwise, you will be re-servicing your set all over after 30 days of usage.good luck,Alex.

Feb 01, 2012 | Hitachi Televison & Video

1 Answer

I have a hitachi 43FDX15B RPTV It appears to have a convergence problem, I've read about replacing the stk IC's but which resistors need to be replaced and what are the values on the DP15k/08 Board?


This model uses two of the STK-392-120 CHIPS and here are most of the usual resistors to suspect or check:

Hitachi AT03411S RK43 RESISTOR Hitachi AT03608S RP22 RESISTOR Hitachi AT03195S RK46,RK54, RK62 RESISTOR, 1.8OHM 1W Hitachi AT03857M R815,R865 RESISTOR, 1/2W 100 OHM Hitachi AT03191S RK50 RESISTOR, 1W 1.2 OHM Hitachi AT03197S RK50 RESISTOR, 1W 2.2 OHM Hitachi AT03199S RK41 RESISTOR, 2.7 OHM 1W Hitachi AT03202S RK42 RESISTOR, 3.3OHM 1W Hitachi AT03204S RK58 RESISTOR, 3.9 OHM 1 WATTThe RK ones are all marked on top and bottom of circuit board---usually if one is bad you will be able to see it is discolored---all are very low value and should read open or good only.

This is a fairly easy set to do this on---the whole convergence board (right side from the back view) is held in with 3 screws and an assortment of plugs--3 plugs are identical (convergence yokes and you need to mark so you get each back in same place)

A row of black snap plugs on the left side and with the screws and other plugs removed the board will lift up and out of the set.

DON'T waste your money on one of the "kits" being sold on the net---you can buy a pair of the chips for about 12 dollars on Ebay and usually only one (if any) of the resistors will be bad---those kits sound like a good idea but at 50-80 you are buying things you will not likely need to repair the set.

Let me know if you have any questions and if this information helped you rate this solution as I do this here for free.

SD TECH


45c74e4.jpg

Dec 17, 2009 | Hitachi 43FDX15B 43" Rear Projection...

1 Answer

Hitachi 43uwx10b. How do i test resistors for convergence? i replaced i/c chips with upgraded stk394-160 and all resistors i was told rk42=3.3ohm/ rk46=1.8ohm/ rk50=2.7ohm/ rk54=1.5ohm/ rk58=3.9ohm/ and...


You have all the resistor are correct! Yes I can Tell you exactly what you need to know and How to Save settings after you adjust convergence, I have to pull out my manual on your hand unit Be right back. first you need to go to front of TV remove front bottom panel to where you can see the front of chassis on the board you replaced ICs there is a small blue contact button with TV on press and hold for 5secs Convergence Pattern should appear! You will need your hand unit to begin to adjust convergences.

Dec 17, 2009 | Hitachi 43UWX10B 43" Rear Projection...

2 Answers

RK46 BURNT CANNOT SEE COLORS ONLY 2 STRIPS DARK AND 2 STRIPS LIGHT. WHAT IS THE OHM VALUE AND DO I INSTAL GOLD STRIPS TOWARDS IC OR AWAY. HATACHI 43FWX20B DP24 JOE


rk46 is 1.8 ohm resistor---rk54 is the same value, rk 62 is 2.2, and Rk 42 is 3.3 ohm. It does not matter which direction it is installed---it is a resistor


If you have any questions feel free to let me know.


SD TECH

Oct 08, 2009 | Televison & Video

1 Answer

Chirping noise hitachi


if you have not replaced IC's replace them an you need to do convergence after good luck

Apr 30, 2008 | Televison & Video

3 Answers

Need resistor value for RK62 on DP2X board for 57SWX20B


RK62 is a 2.2ohm 1 watt metal oxide resistor hitachi part number 0700054M any 2.2ohm 1 watt resistor will work although it does have to be metal oxide(flame resistant) for safety purposes.

Mar 24, 2008 | Hitachi 57SWX20B 57" Rear Projection...

2 Answers

Resistor ohm values??????


RK42 = 2.2 , RK46 = 1.5 , RK58 = 3.3 , RK52 = 1.8 , RK 50 = 2.2 , RK54 = 1.5

Aug 28, 2007 | Hitachi 53UDX10B 53" Rear Projection...

Not finding what you are looking for?
JVC AV-48WP30 48" Rear Projection Television Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69808 Answers

easy alberta
easy alberta

Level 2 Expert

132 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...