Question about Hoover Nextra HNF 3167 Top Load Washer

1 Answer

Hoover 750L top loader washing machine

When we start a cycle, the water only dribbles into the machine. The water runs fine thru both hot and cold pipes but not into the basin.
Help please

wont agitate, wont spin dry fully

Posted by on

  • 2 more comments 
  • faulty Jan 30, 2008

    already tried wont wash and wont spin dry

  • faulty Jan 30, 2008

    the water fills ok,it just wont wash the clothes and will empty ok but wont spin dry either,And dose the same thing for the different cycles.the machine is a hoover 750LC,
    7.5kg heavy duty top loader.

  • faulty Jan 30, 2008

    How do i remove the iner bowl to see if a sox or something else is causing the problem.?

  • faulty Jan 31, 2008

    I turned the belt manually and it moves freely, so I checked the belt and the belt is ok too.Looks like the lid switch is working too.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

The load might be unbalanced, and will not spin at full speed as it could damage the machine. Try reloading the machine

Goodluck,
Dont forget to rate me as Fixya..

Posted on Jan 30, 2008

  • 2 more comments 
  • Priya darshan Jan 30, 2008

    Start a new wash cycle and then turn the temp selector to cold.....is it filling with cold water? Now try the hot, is it filling with hot water?


  • Priya darshan Jan 30, 2008

    try replaceing the lid switch if washer will not spin

  • Priya darshan Jan 30, 2008

    If the clothes are not washing then It is a belt problem. Try to move tub manually first, in case it move smoothly -open the front panel, the belt should be between the motor and the drive pulley (lower front). In case it torn or not in its place, you should replace it.
    In case it doesn't move smoothly - maybe that a sock or other piece of clothing get between the clothes tub and the outer tub and prevent tub's spining. If this is the situation, it should be removed.

  • Priya darshan Jan 31, 2008

    f the agitator is not turning, then the problem is wid motor coupling If it won't
    spin (but sounds like it wants to with the lid down), the clutch needs
    replacing. More than likely, the transmission will need replacing too
    (oil has leaked out of the transmission onto the clutch). If that IS
    the case, and you ONLY replace the clutch.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WI815 Intuitive Eco - no cold water


IW Intuitive Eco.
Water valves have a rubber diaphragm that wares out
after some time,
So yes you are right water valves need replacing.

Apr 21, 2014 | Fisher and Paykel Washing Machines

2 Answers

Hoover 700l Cold water is not fillingproperly. Only a verey small dribble comes into the machine. I have reversed the hot and cold hoses, making sure that the setting is on "hot". Problem...


Clogged screen in fill valve on cold side. Remove hose from cold side on valve. Pull screen out. Wash under hot water, and re-install.

Jan 23, 2011 | Washing Machines

1 Answer

My washer will not fill with water or do any functions when i turn the dial


My Hoover 7700l ...on "fill" cycle, the water dribbles in. Takes hours to fill so we use buckets to reach the required level.

Tried: Swapping cold and hot water inlet hoses, making sure that dial is in "hot". This solved the problem for filling, BUT when "rinse cycle appoars, it's back to the dribble again.

any ideas?

Jan 23, 2011 | Maytag LSE7806A Top Load Stacked...

1 Answer

Hoover 550M washing machine - taking ages to fill, water is just dribbling out. Was fine when started, lifted lid to put in clothes and now only dribbling out. Water pressure in rest of house seems to be...


Check the inlet screen on the hose connection on the back of the machine. This may be clogged with debris, also make sure you hose is not crimped. You can unhook the inlet hose and put it in a bucket and turn it on to see how much water is actuall coming thru that hose. I suspect some type of blockage in the inlet.

Nov 11, 2010 | Hoover HTC243 Top Load Washer

2 Answers

Cold water dribbles in rinse cycle, hot and warm water fine


If you check the warm water flow you'll likely find it is HOT...and not warm. Check the faucet end of hose to see if screen is clogged. Should be screened washer with the dome portion of the screen facing out at you. Remove it and clean with brush to remove grit or scale from screen. If you find nothing there you need to replace the water fill valve located at the other end of the hoses. Good Luck

Aug 23, 2009 | Kenmore 22422 Top Load Washer

2 Answers

Hoover 750L top loader washing machine


I had this problem. I alternated the hot and cold water valves (changing over the wiring) and then hot tap then dribbled instead of the cold. Replacement part i believe is around $35AU

Dec 29, 2007 | Washing Machines

2 Answers

Lg washing machine wft855a top loader


Following up my comment from yesterday, I took the machine apart and discovered that the black rubber cover on the valve that releases the cold water had perished and cracked, and wasn't opening properly.
I tested the hot and cold solenoids and everything checked out ok. Was just the cold valve sticking.
The wash cycle was working because I was using hot/warm water. As the rinse cycle needs cold water to get started, it was not working and the rinse and spin cycles wouldn't complete.
I have swapped the valves over for now (put the working hot one on the cold side and am using cold water only). It's working while I order a replacement...

Sep 07, 2007 | LG WFT1071TP Top Load Washer

5 Answers

Problem with Hoover 200M


Hi All
The solution is a faulty solenoid valve, either the hot or cold valve depending what temperature you are using.
Replacing the valve is easy turnoff machine unscrew hose, remove 3 srcews to lift control cover, slide out locking tab, unclip wires the replace valve which cost about 30-$40

Tobor

Aug 22, 2007 | Hoover HTC243 Top Load Washer

Not finding what you are looking for?
Hoover Nextra HNF 3167 Top Load Washer Logo

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...