Question about Kenmore 73952 Gas Dryer

1 Answer

Kenmore gas dryer model # 87566100

Dryer runs, igniter glows, doesnt light. procedure starts over in a few minutes with same results. control valve, ignition sensor, and igniter have been replaced.

Posted by on

  • 1 more comment 
  • tdcreutz May 29, 2008

    same deal!

  • kilroq May 30, 2008

    no, those were all good . It was the main control knob. thanks anyway

  • Anonymous Mar 19, 2014

    dryer starts for a few minutes and shops and display SRV CLL on screen and if you wait fora few minutes it will start back up but runs for a few minutes and cuts off again and repeat the same steps

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 110 Answers

BAD SOLENIODS OR THERMAL SAFETY

Posted on May 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Kenmore gas dryer 80series model 110.c72852101


if you hear the valve clicking but no gas the valve is bad.when the burner lights theres a probe that senses that it is lit and sends a microvoltage back to the controller to tell its lit.check to make sure all ground wires are grounded to a clean metal surface.

Oct 03, 2007 | Kenmore 74602 Gas Dryer

1 Answer

Kenmore gas dryer #41793142300 electronic start doesnt heat up


if you first have heat and then like 10 to 20 minutes later no heat you could have bad gas coils,on most gas dryers there's a plastic cap you can pop off on the front panel so you can look in and see the ignitor,if at first the ignitor glows orange and the flame lights then after a few minutes the ignitor glows orange and the flame doesn't light you have bad gas coils,they are located on the top of the gas valve,easy to change.part number 5303931775 go here and look at part 71
http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Dryer-Parts/Model-41793142300/0582/0151200/R0310102/00005?blt=06&prst=0&shdMod=41793142300

Mar 25, 2013 | Dryers

1 Answer

Hi, I have a Kenmore gas dryer model 417. I can't


Sounds like the coils on the gas valve are bad.

May 26, 2011 | Kenmore Dryers

1 Answer

Kenmore series 500 gas dryer not heating up. model # 77542600 Other than the ignitor what could be the problem?


Check the coils on gas valve. If igniter glows bright & no CLICK sound heard after a few seconds of igniter glowing, coils are bad, or flame sensor if so equiped

Feb 13, 2011 | Kenmore 500 6952 Dryer

1 Answer

Model 110 72712101 kenmore gas dryer will come on run about 2to3 minutes then goes off after a short the glow will come on again but will not relight.


Watch the igniter. Does it glow bright orange, then shut off without igniting the gas? (When the gas ignites there's a large blue flame.) If so, there may be defective coils on the gas valve. Mounted on the top of modern gas valves, there are black electrical coils. The coils, when energized, open the gas valve. If one or more of the coils are defective, the valve doesn't open and the gas cannot ignite. Because it's often difficult to properly test the coils, it's usually best to replace both (all) of them at the same time. Here is a link to the parts you need.

Jan 02, 2011 | Kenmore 63942 Dryer

2 Answers

Kenmore dryer heats at first then quits


You may have a bad thermocouple. The thermocouple is what "tells" the control unit that the flame is present. If it doesn't tell the control, the control turns the gas off to prevent an explosion.

Jan 02, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Gas Dryer ignites then stops heating after ten minutes.


If the glow bar comes back on and the gas does not light,replace the gas valve coils. If the ignitor does not come back on,replace the flame sensor.

Sep 01, 2009 | Kenmore Dryers

1 Answer

Kenmore gas dryer mod.110-73942. burner comes on as normal. After 5-10 minutes running Cycles off, igniter ( new) glows but no burner ign. Also replaced the sensor adjacent the igniter.


The gas valve coil is bad. When the ignitor is glowing the gas valve should open and allow gas in to be ignited. Change the gas valve.

Aug 05, 2009 | Kenmore 63942 Dryer

1 Answer

Kenmore Elite Dyer Model # 11071082000


Hi. thanks for the question. the problem you have is with the coils ,on the gas valve. 2 little coils . replace them. thanks the appliance doc

Sep 30, 2008 | Kenmore 72802 Gas Dryer

Not finding what you are looking for?
Kenmore 73952 Gas Dryer Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Tim Whalen

Level 3 Expert

3072 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...