Question about Fahrenheat (FFH1614) Wall Mounted Panel Heater

1 Answer

Wall mount Heather no heating

I have 2 wall mount heather, and one of them is not workign the air is cold. What should I do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Check the breaker is not blown. if it is reset it. if you have the electrical knowledge see if you have 240 volts at the heater.

Posted on Feb 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3509622 model number furnace heats up but does not blow any air out. Neither hot or cold air.


You are describing a Convection heater , they do not have any fans inside.

Nov 08, 2013 | Thermos 3509622 Heater

1 Answer

The heatpump blows out air ok but no heat?


You are probably going to have to call a Hi Vac repair as your freon is probably too low to operate your Heat Pump properly. The only difference between the Air condition side and the heat side is a reversing valve that takes the heat produced by the Air Conditioning (cold) side and sends it into your house and exhaust the cold air out side. If the pump cannot produce heat from the expansion and compression of the freon, then no heat. You may also want to check that the pump is running as it is protected by two large BUSS fuses on the AC power to the heat pump and if any one or both of those fuses are blown, then no power to the Heat Pump. There should be an 8 inch square box mounted on a wall next to the heat pump that supplies 220V to the pump.

May 17, 2011 | Heating & Cooling

1 Answer

Williams 3003622 Wall Mounted 30,000 BTU The pilot light goes out when the main flame shuts down. The pilot light will stay lit for days when heat is not called for but when heat is called for the furnace...


I'm having the same exact problem... At first we thought was the vent... but the way the flames goes out... it seems that there is "not enough oxygen" more than "blown out by the wind"... right after both main & pilot goes out, I can't even light any external flame inside the chamber... and it doesn't feel like the outside cold air coming in... it just feel like there is some sort of gas in the chamber that's so strong, it prevents flame... and the only thing I can think of is that it doesn't have enough oxygen, but too much natural gas, and flame can't sustain.

Nov 02, 2010 | Williams 3003622 Ceramic Wall Mounted...

1 Answer

Cadet C151 heater not producing warm air.


take your tstat off jump out the wires red green white together. if it works like that then your thermostat is bad. if it doesnt then it is in the unit.

Mar 24, 2010 | Cadet Manufacturing Com-Pak Plus C151...

1 Answer

Fan heather not work


If you have the model number of the unit ( a series of Letters with a few numbers in it). You can go to www.desatech.com and find the manual for the unit under "Wall Heaters." In the manuals there are usually troubleshooting guides. Hope this helps!

Mar 15, 2010 | Desa International Blower Glow Warm Wall...

1 Answer

What is easy way to replace the thermostate in


Hi, that thermostat should be a wall mount. This heater has only 2 wires and any "Heat only", "millivolt" thermostat will work. Remove the old T-Stat and mount the new one on the wall, only 2 wires and less than a volt so no shock danger, doesn't even matter which wire goes where. Good luck and comment back if you need any help.

Jan 09, 2010 | Cozy Heating & Cooling

1 Answer

Williams debonair wall heater + pilot light problems


THE flame from the pilot should shoot past the thermo-couple and heat this up and make a small amount of mili- amps to prove the pilot light is lit. ..So if the flame doesn,t go past the thermo-couple it won, make mili-amps or its tme to change out the thermo-couple, They only cost lest than $8:00 and you can change it!

Dec 22, 2009 | Williams 3003622 Ceramic Wall Mounted...

1 Answer

Remote control working with fireplace.


try www.dimplex.com go to customer sevices they should be able put you on to a local dealer in your area

hope this is of some help

Dec 13, 2008 | Dimplex DS5603 Heater

3 Answers

Wall gas furnace


look inside the control panel of the heater. look for a 120 volt to 24 volt transformer.  There may be a fuse on the transformer secondary.  The thermostat switches a hot 24 volt wire so you won't find a common at the thermostat.

Nov 13, 2006 | Empire GWT-25 Wall Mounted Panel Heater

Not finding what you are looking for?
Fahrenheat (FFH1614) Wall Mounted Panel Heater Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fahrenheat Heating & Cooling Experts

paulcarew

Level 3 Expert

2035 Answers

Brad Brown

Level 3 Expert

13732 Answers

yadayada
yadayada

Level 3 Expert

63328 Answers

Are you a Fahrenheat Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...