Question about D-Link DES 3226 (DES-3226) 24x10/100 Mbps Networking Switch

1 Answer

ASM200 tenor password

I need help , i forgot my admin password how I break it or setfactory default the systems please help me
thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

The only way is to send to D-Link support your equipment's serial number and MAC address, and they will generate a master password.

you can view the manual for more information

http://203.126.164.140/products/view.asp?productid=DES%2D3226SM

Posted on Jan 29, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Forgot admin password and don't have. Recovery disc


You would need to take to a repair shop to re-install the system for you.
Or search on ebay / amazon for a windows ___ disk, but make sure it matches the version you have printed on the COA on the bottom of your laptop.

25617761-cbt13vi4zbmnff1d5zdl02jb-2-0.gif

Mar 30, 2015 | Computers & Internet

1 Answer

I forgot the password for the 192.168.1.1 page what do i do


Hi,

Please do the following.
1. If you have changed the default password you will have to reset router and the password will be set to the default password. To reset the router to factory default keep the reset button pressed for 15 seconds while the router is powered on the reset button is located on the back of the router inside a small hole which needs to be pressed using some pointed object like a pen or a pin.
NOTE** its importaint to note that if you reset the router to factory defaults you will lose all the configuration and you will have to reconfigure the router***

2. if you have not reset/ changed the password ever try using the following user name and password

username password
admin admin
system admin
root root
admin
System
root

Aug 18, 2011 | Gateway Wireless-B Router (wbr-100)

3 Answers

I cant connect with the router because i forgot the password


Default admin username, cisco. Default admin password, cisco

Jul 28, 2011 | Cisco (1841) Router (cisco1841)

1 Answer

NEED QUINTUM PASSWORD RESETTING


The detailed description of Configuring Terminal Software/Assigning IP address to Tenor DX is given below.If you need only RESETTING GOTO STEP 18.

1.From your PC, click on Start> Programs> Accessories> Communications> HyperTerminal. The Connection Description is displayed.

2.Enter a connection name (i.e., name for each unit such as Tenor DX 1 and click Ok.

3.Choose the connection port on your PC from the Connect Using drop down list box (i.e., Direct to Com1). Click Ok. The Com1 Properties window will be displayed. See Figure 3.

tinualbinale_22.jpg
4.From the Bits Per Second drop down list box, choose 38400.

5.From the Data Bits drop down list box, choose 8.

6.From the Parity drop down list box, choose None.

7.From the Stop bits drop down list box, choose 1.

8.From the Flow control drop down list box, choose None. Click Ok. A connection to the Tenor unit is established.

9.Click on Call>Call. A connection to the unit will be established. The login prompt appears.

10.Enter a login name. The default login name is admin.

11.Enter a password. The default password is admin. (Once you are up and running, changing the password is a good idea for security purposes). Step through each of the following parameters and enter the correct values for your installation: IP address, Subnet Mask and Default Gateway.

12.At the Quintum prompt, type ei to reach the Ethernet prompt and then type config to change to the configuration mode.

13.To set the IP address, type set ipa followed by the IP address.

14.To set the Subnet Mask, type set subnetmask, followed by the subnet mask.

15.Type siprd to change to the Static IP Route Directory.

16.To set the Default Gateway IP, type change 1 g followed by the IP address for the default gateway IP.

17.Type submit.

18.Type maint to reach the maintenance mode and then mc. Type reset. A confirmation message will ask if you want to reset the unit. Type yes to reset the unit. The reboot enables the Tenor to incorporate the new settings.

19.Once the IP information is set, you are ready to configure the unit.

Jun 04, 2011 | Quintum Tenor DX2060 (501-0122-00)...

2 Answers

How to recover the password for 198.168.1.1


You will need to reset it then it will come to default
password. unplug power cable then while powering on press the reset button simultaneously.
ok
A user name and password prompt will appear. Type in admin (lower case) for the username and password. The username and password admin are the default username and password of TP-LINK Routers.
ok link
http://www.tp-link.com/support/showfaq.asp?id=10

Jan 07, 2010 | Computers & Internet

1 Answer

Cant login never had username or password if i did i forgot


Depending on which revision you have there are two possibilities

Default Username is: admin
Default Password is: password
or
Default Username is: admin
Default Password is: admin

If neither of these work - you may have setup a new username and password and forgot - on the router you will see a reset point - reset the router to factory defaults and the username and passwords above will now work.

If this helped you then please help me and vote kindly, thank you.

Oct 14, 2009 | NetGear WGR614 Router

3 Answers

Forgot username and password for Lynksys


Hi, Sweet baby,

The default username for the Linksys router is blank and password is "admin"

I hope this information allows you to resolve this issue.

If I have helped you, please help me, and rate this suggestion the highest FixYa rating. If you cannot rate this post with the highest rating, then please comment to this post and I will try to help you further.

Regards
Anand

Jul 13, 2009 | Linksys Wireless-G WRT54GS Router...

1 Answer

I have a Toshiba studio 281c, we forgot the ADMIN password, help!


the default password should be "123456".

If u did changed the default password, then u need to enter setting mode 08 - 263 to check or edit the password.

Mar 10, 2009 | Toshiba E-STUDIO 450 Copier

1 Answer

Who can help solve my problem


The CM stands for "Configuration Manager", in other words, that is the GUI. The Tenor firmware either starts with a P or an S (e.g. P104-11-00 or S105-01-01)

Sep 17, 2007 | Quintum Tenor ASM200 (501-0132-00)...

1 Answer

Asm 200


There are 6 potential volume adjustments for an Analog Tenor.
Rx & Tx at the Phone, Line & IP - Adjust them carefully, 1 dB at a time. There are some tests that can be run to test impedance too, which will ultimately affect audio quality.

http://www.quintum.com/support/xplatform/telco/Tenor_MFG_Test_SecondGen.pdf

Feb 23, 2007 | Quintum Tenor ASM200 (501-0132-00)...

Not finding what you are looking for?
D-Link DES 3226 (DES-3226) 24x10/100 Mbps Networking Switch Logo

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2268 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...