Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

Wd52525 the timer led blinking. no picture no sound

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 4,402 Answers
Re: wd52525

>>The first thing to do is a system reset using the recessed button on the front panel.
>>If that does not work, unplug the set and let it sit overnight
SYSTEM RESET button with a pointed item like the end point of a paperclip
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.

For example, 3 flashes, then 7 flashes = 37.

Here are the error codes, and the corresponding problem:

12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Posted on Jan 29, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a wd52525 the status light keeps blinking

There are 3 different LEDs on the front of this televison. The TIMER will blink green. The STATUS will blink orange and the LAMP will flash red or orange depending on if there is a failure or if the lamp timer is showing over 5000 hours.

If I answer your question directly and the status is blinking a steady orange light, then you have left the side filter cover or the front lamp cover off or they are loose.

Also holding the menu and device buttons together until the timer light blinks will reveal a code that will help in diagnosing your problem. Goodluck.

Jul 04, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer


The Capacitors on the DM board need replaceing. The V26 DM repair kit from will usually repair that issue. The kit contains the capacitors and the CD with instructions.

Dec 14, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Model WD-57731 LED Timer Light

You have a dm board problem could be the capacitors or you may need to change the entire board.

Sep 16, 2009 | Mitsubishi WD-57731 57" Projection HDTV

1 Answer

Blinking green light under 'Timer' flashes there is no picture

If you have a green blinking LED that runs continuosly, its the widespread problem of failures of capacitors on several circuit boards in the TV. Currently Mits is having authorized service centers remove the chassis and send it them for rebuilding. Its an expensive and time consuming repair.

Feb 17, 2009 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Turn on the TV and only Timer light is on , no sound & picture

after holding down the menu and device the led will blink a two digit error code such as 3 blinks pause then 4 blinks then repeat that sequence a couple of times. Need that blink code to help let you know whats going on. The 34 code means lamp abnormality which translates to the power Pwb capacitors have most likely failed.

Jan 23, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

No picture no sound

it sounds like the chassis has gone bad. check out

Dec 31, 2008 | Mitsubishi WD-52525 52" Rear Projection...

2 Answers

Six (6) blinks on the Timer/Standby led

6 blinks means lamp thermal fuse blowing, replace thermal fuse.

See here

Aug 30, 2008 | Sony KP-57WS500 57" Rear Projection...

2 Answers

Power comes on, red light flashes on timer/standby but no picture

Need the model number of your set and also how many times is the led blinking? Please respond to this same post

Jul 25, 2008 | Projection Televisions

2 Answers

No picture no sound


Probably, the selftest fails while turning on. If this is the case, press input&menu buttons at the same time for 5 seconds, then the green led will start to blink. Let me know how many times the led blinks.


Mar 01, 2008 | Mitsubishi VS-50609 50" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66518 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides