Wii tony hawk skate board controller loses connection

As long as you are following the instructions properly, I would say you have a defective board. This accessory is notorious for failing even brand new straight out of the box. In fact, they are so unreliable that most consignment game shops will not even consider purchasing them from you.

If you are simply finding it difficult to connect the board because you lack the proper instructions, here you go: How to sync Wii Tony Hawk Ride Skateboard (not my vid, but this is exactly what you need to do).

First turn on the little box you plug into the usb of the wii,then turn on board after make sure the wii sencer bar is also able to pick up board as well the red light will flash just let it go and should work make sure the blue lights are on on the board.

I had the same problem. I solved it and got the board to calibrate immediately when I replaced the brand new batteries with used batteries. Brand new batteries apparently make the lasers very sensitive. You have less sensitive sensors with the used batteries. I just took some AA's out of my cable remotes. The game is awesome once you get it calibrated. I felt your pain for an hour or so.

close all the curtains in the room, turn off all the lights,cover t.v. screen with a sheet, raise the board approximately 3 feet off the ground on cardboard boxes, place wii controller box in front of t.v.(i laid it flat on its side) so it was same level as the skate board, leave the room after several trys this finally worked for us! be sure everything else in room is turned off.,

regarding this ....... without knowing much about the wii console you can easily repair with the help of repair guide ...........

Click Here to Download

IT TOOK 1.5 HOURS TO SYNC UP AND CALIBRATE A NEW TONY HAWK RIDE SKATE BOARD WITH A Wii.
THE ON-LINE DIRECTIONS AND TROUBLESHOOTING = SUX!.

PLEASE FOLLOW THESE DIRECTIONS IF YOUR HAVING THE SAME ISSUE:
1) Remove skateboard battery's for 1 minute
2) Reinstall 4 new/fully charged AA Battery's in the Tony Hawk RIDE Skateboard.
3) Plug the Tony Hawk Wireless USB Dongle into the "upper" WII USB Port,
Turn on the WII,
Insert the Tony Hawk Ride game disk
Keep pressing A on the WII Controller till you get to the Error Screen saying:
*Unable to SYNC up the skateboard with the WII*
4) Make sure the WII and the plugged in wireless USB Dongle are laying on the floor in front of the wireless skateboard "sideways" with the wireless dongle towards the right side of the WII.
5) The directions state to 1st press the wireless USB dongle reset/Sync button, then the so called Start button on the board, which did not work 100 different times.
6) Instead (on the side of the board) all 4 of the blue LED lights were on. Now press and hold the button which is the Start/Home/blue little house/C- looking Button on the side of the board for 5 seconds. The Blue LED lights should now all be off!
7) Now press the WII Wireless USB Dongle reset/Sync button.
8) After the Dongle sync

IT TOOK 1.5 HOURS TO SYNC UP AND CALIBRATE A NEW TONY HAWK RIDE SKATE BOARD WITH A Wii.
THE ON-LINE DIRECTIONS AND TROUBLESHOOTING = SUX!.

PLEASE FOLLOW THESE DIRECTIONS IF YOUR HAVING THE SAME ISSUE:
1) Remove skateboard battery's for 1 minute
2) Reinstall 4 new/fully charged AA Battery's in the Tony Hawk RIDE Skateboard.
3) Plug the Tony Hawk Wireless USB Dongle into the "upper" WII USB Port,
Turn on the WII,
Insert the Tony Hawk Ride game disk
Keep pressing A on the WII Controller till you get to the Error Screen saying:
*Unable to SYNC up the skateboard with the WII*
4) Make sure the WII and the plugged in wireless USB Dongle are laying on the floor in front of the wireless skateboard "sideways" with the wireless dongle towards the right side of the WII.
5) The directions state to 1st press the wireless USB dongle reset/Sync button, then the so called Start button on the board, which did not work 100 different times.
6) Instead (on the side of the board) all 4 of the blue LED lights were on. Now press and hold the button which is the Start/Home/blue little house/C- looking Button on the side of the board for 5 seconds. The Blue LED lights should now all be off!
7) Now press the WII Wireless USB Dongle reset/Sync button.
8) After the Dongle sync

You probably need to sync the controller to the system. I am not sure if it works the same as the remote, but if you have the instruction booklet, it should tell you how to sync the controller.
Usually, there should be a sync button on the controller. Press it, and then press the sync button behind the sd compartment on the console.

idk try plugging it again

Press the button on the dongle, then press and HOLD the power button on the board until it stays solid. had the same problem hope this works