Question about Washing Machines

1 Answer

Slow spin on Whirlpool G6234DT1

Washer spins but weakly. can stop barehanded. all else works fine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 45 Answers
Re: slow spin on Whirlpool G6234DT1

Check the belt, it must have gone loose. it can be replaced. but remove the belt and take it to the hardware store for a exact replacement.

Posted on Jan 27, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

How to fix the spin cycle on my Whirlpool washer?

Usually Debra you have to replace the motor when this happens motor is weak and heating up cutting out to soon ..Hope this helps

Mar 02, 2015 | Whirlpool WFC7500VW Washer

1 Answer

Won't spin fast when fully loaded

You may have a weak clutch. If you can stop the washer during spin by hand, that's what it is.

Jan 26, 2014 | Kenmore 24422 Top Load Washer

1 Answer

Washer stopped during spin cycle

Hello, try to checked the pump filter, and the pump is actually working. then I would suspect a draining problem.
If filter clean and pump works fine then it could be a control module fault. if this were the case, then it would probably be wiser to purchase a new washer.

Jun 04, 2010 | Whirlpool LTE5243D Top Load Stacked...

2 Answers

Whirlpool type 111 model LSQ9200LQ3 washer not

I have a whirpool model:lsq9200lq3, and recently it has stopped working. when ever you turn it on, its fine and the water fills up normally and right before it gets to the spinning cycle the machine makes a grinding noise like if something is stopping the motor from spinning, and it dosent spin inside the washer. if anybody has any suggestion It would be great thank you.

Jan 30, 2010 | Whirlpool Washing Machines

1 Answer

Whirlpool washer spin cycle works off and on

no the slowing down maybe caused by a sticking clutch and as before the lid switch may also be broken if when you depress it the reason i'll give is if you bump it it sometimes starts up replace the lid switch and once done the circiut will close properly then the delicate cyc should work

Aug 23, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool super capacity washer spin cycle stop working

Sounds like you need a new lid switch. Click HERE for prices.

Apr 19, 2009 | Maytag HAV2558 Top Load Washer

1 Answer

Won't spin heavy loads

you need a new transmission it will slowly get worse until it stops working

Dec 23, 2008 | Whirlpool LSN1000LW Top Load Washer

1 Answer

Slow or no spin

It's direct connected to motor!!!
Solution is to change brush which go on collector!!!
This is inside the motor!!!
It's not so complicated to do but must be carefully!!
good luck

Jan 29, 2008 | Washing Machines

1 Answer

Maytag Performa Washer spins fine but stops instantly

Check the unit next time it is in the spin open the lid up does it do the same thing?? if so it is working ok that is the Brake in the unit doing it Job but if it is really loud it maybe going out??

Jan 26, 2008 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides