Question about Adcom GFR-700 Receiver

1 Answer

Adcom GFR 700 HD Remote code?

I have a Adcom GRF 700 HD 5.1 Receiver with a GRC 850 remote and I would like to put the functions into my new Verizon Fios remote.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

If the remote is infrared (IR), you'd need the codes if the Verizon remote is not a 'learning' remote - in other words, facing the two to each other and transmitting/receiving between them. So, assuming the Verizon is not a learning remote, you'd need the IR codes. Some can be found in the back of users manuals but if not, contact the manufacturer and ask for the codes. They'll usually send them to you in a file.

Posted on Jan 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rf20 code for directv HR34/700 receiver


Check these codes:

503, 505, 515, 548, 579, 580, 581, 582,
583, 584, 586, 587, 625, 633, 634, 691,
698, 701, 708, 714, 715, 716

Jul 22, 2012 | Universal Remote Control RF20 LCD Remote...

1 Answer

Adcom GDR-700 hd I2C error code?


just check www.ebcelectronics.com they can repair your receiver. Here is a link to GFR-700 repair service

Feb 12, 2012 | Adcom GFR-700HD 7.1 Channels Receiver

1 Answer

I had to get a new TV HD receiver. How do I get it programmed to my MX-850 remote? It will not turn my TV receiver on when I push the on button. I have to manually turn on the receiver.


What kind of receiver did you get? DirecTV, Dish, or something else? This remote comes with software and cables you can connect to your computer. Once you install it, and connect the device, you can program it to connect with your specific electronic components. You may need your existing/original remotes to help get everything set up, but usually that is a one-time process.

Oct 10, 2011 | Universal Remote Control MX-850 LCD Remote...

1 Answer

Sound seems to coming from only one of my front speakers(left side). what am i missing? I can't seem to find a balance setting on the menu


Traditional Balance Controls are gone with the dinosaurs of stereo audio equipment.

Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Adcom-GFR-700-Receivers-manual/id/582dj599/t/2/

You may just have a speaker or speaker wire loose/failing. Swap them to isolate to an internal or external failure.

There isn't enough adjustment in the setup to make any channel completely silent.

Use test tones to diagnose it. Page 36.

Apr 25, 2011 | Adcom GFR-700 Receiver

1 Answer

There is no sound from the center & surround channels, but the test tone works fine


Hello
If the test sound is OK, then the problem might be in connections or input, Check these
Good Luck

Dec 09, 2010 | Adcom GFR-700 Receiver

1 Answer

Adcom GFR-700 7.1 Receiver. No output to powered subwoofer. Had unit repaired under warranty (new audio board), and now, a little over a year later the same problem has occured. Is there an inherent...


I am not aware of any known defect, but it might be helpful to know what was done the first time to address this problem. If the audio board was replaced, that basically includes the "crossover" circuitry that feeds the sub out. It is quite possible that that circuit has failed. While unusual for the same problem to recur, it does happen. It would also suggest that rather than the actual problem being solved, perhaps only the resultant symptom was addressed. The bottom line here is that additional research must be done on the circuitry inside the machine.

Keep us posted.

Dan

Oct 29, 2010 | Adcom GFR-700 Receiver

1 Answer

Where can I purchase a GRC-810 remote for an Adcom GTP-880


I have a GRC 815 remote for sale : jjohndub@gmail.com email me, me can work it out

Oct 26, 2009 | Adcom Audio Players & Recorders

1 Answer

Remote will not program


See this website. It worked for me and I've never soldered before.

http://mysite.verizon.net/amp68/

Sep 02, 2008 | Kenwood VR-507 Receiver

2 Answers

Universal TV remote control


Target sells a GE Universal Remote Control, 5 Device with learning feature. I can't say if it works with your Verizon DVR, but its code for the Akai LCT3285TA is 1139. If you have the Verizon's remote, you should be able to use the learning function to make the GE control it - that's if the GE doesn't have a built in code that will work for this DVR.

Apr 26, 2008 | Akai LCT3285TA 32 in. LCD Television

Not finding what you are looking for?
Adcom GFR-700 Receiver Logo

Related Topics:

454 people viewed this question

Ask a Question

Usually answered in minutes!

Top Adcom Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5547 Answers

Computer Links

Level 3 Expert

2386 Answers

David Burbee
David Burbee

Level 3 Expert

1871 Answers

Are you an Adcom Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...